Oscam & Smargo viasat 093E

There are 5 replies in this Thread which was already clicked 8,416 times. The last Post () by Syntaxmovies.

    Been struggling to get this setup to work.


    I´ve got the card working just fine in the internal reader of the DB but I don`t wanna use this cause afraid of burning the card.


    My setup is:


    800SE Original
    Newnigma 3.2.2
    Oscam using dvbapi


    Smargo v1.4 reader settings: Auto and dreambox kernel.
    I think I´ve got all usb kernels installed (the ones from online softmanager)


    Here´s my log:


    2011/09/15 12:02:51 0 s >> OSCam << cardserver started, version 1.20-unstable_svn, build #5944 (mips-tuxbox-linux)
    2011/09/15 12:02:51 0 s version=1.20-unstable_svn, build #5944, system=mips-tuxbox-linux, nice=-10
    2011/09/15 12:02:51 0 s client max. idle=120 sec, debug level=0
    2011/09/15 12:02:51 0 s max. logsize=1000 Kb, loghistorysize=4096 bytes
    2011/09/15 12:02:51 0 s client timeout=5000 ms, fallback timeout=2500 ms, cache delay=0 ms
    2011/09/15 12:02:51 0 s Cannot open file "/etc/tuxbox/config/oscam.services" (errno=2 No such file or directory)
    2011/09/15 12:02:51 0 s userdb reloaded: 1 accounts loaded, 0 expired, 0 disabled
    2011/09/15 12:02:51 0 s signal handling initialized (type=sysv)
    2011/09/15 12:02:51 0 s can't open file "/etc/tuxbox/config/oscam.srvid" (err=2 No such file or directory), no service-id's loaded
    2011/09/15 12:02:51 0 s can't open file "/etc/tuxbox/config/oscam.tiers" (err=2 No such file or directory), no tier-id's loaded
    2011/09/15 12:02:51 0 s can't open file "/etc/tuxbox/config/oscam.provid" (err=2 No such file or directory), no provids's loaded
    2011/09/15 12:02:51 0 s can't open file "/etc/tuxbox/config/oscam.ird" (errno=2 No such file or directory) irdeto guessing not loaded
    2011/09/15 12:02:51 0 s monitor: initialized (fd=6, port=988)
    2011/09/15 12:02:51 0 s camd35: disabled
    2011/09/15 12:02:51 0 s cs378x: disabled
    2011/09/15 12:02:51 0 s newcamd: initialized (fd=7, port=34000, crypted)
    2011/09/15 12:02:51 0 s -> CAID: 093E PROVID: 000000
    2011/09/15 12:02:51 0 s radegast: disabled
    2011/09/15 12:02:51 0 s http thread started
    2011/09/15 12:02:51 0 s reader check thread started
    2011/09/15 12:02:51 0 s check thread started
    2011/09/15 12:02:51 0 s creating thread for device /dev/ttyUSB0
    2011/09/15 12:02:51 0 s loadbalancer: can't read from file /tmp/.oscam/stat
    2011/09/15 12:02:51 0 s waiting for local card init
    2011/09/15 12:02:51 540028 h HTTP Server listening on port 10001
    2011/09/15 12:02:53 53E838 r reader viasat initialized (device=/dev/ttyUSB0, detect=cd, mhz=357, cardmhz=357)
    2011/09/15 12:02:55 0 s init for all local cards done
    2011/09/15 12:02:55 0 s anti cascading disabled
    2011/09/15 12:02:55 5421E8 c plain dvbapi-client granted (localuser, au=on (1 reader))
    2011/09/15 12:02:55 5421E8 c dvbapi: 3 entries read from oscam.dvbapi
    2011/09/15 12:03:17 5421E8 c dvbapi: [ADD PID 0] CAID: 090F ECM_PID: 1FA3 PROVID: 000000
    2011/09/15 12:03:17 5421E8 c dvbapi: [ADD PID 1] CAID: 093E ECM_PID: 1FA2 PROVID: 000000
    2011/09/15 12:03:17 5421E8 c dvbapi: new program number: 1F9A (090F:1F9A unknown)
    2011/09/15 12:03:17 53E838 r Error processing ecm for caid 093E, srvid 1F9A (servicename: 093E:1F9A unknown) on reader viasat.
    2011/09/15 12:03:17 5421E8 c dvbapi: try pids again #1
    2011/09/15 12:03:17 5421E8 c localuser (093E&000000/1F9A/88:2952): not found (4 ms) by viasat (of 1 avail 1)
    2011/09/15 12:03:17 5421E8 c dvbapi: try pids again #2
    2011/09/15 12:03:17 5421E8 c localuser (093E&000000/1F9A/88:2952): not found (0 ms) by viasat (of 1 avail 1)
    2011/09/15 12:03:17 5421E8 c dvbapi: try pids again #3
    2011/09/15 12:03:17 5421E8 c dvbapi: can't decode channel
    2011/09/15 12:03:17 5421E8 c localuser (093E&000000/1F9A/88:2952): not found (0 ms) by viasat (of 1 avail 1)



    oscam.conf


    [global]
    usrfile = /emu/log/oscamuser.log
    logfile = /var/log/oscam.log
    disablelog = 0
    disableuserfile = 1
    fallbacktimeout = 2500
    Nice = -10
    WaitForCards = 1
    PreferLocalCards = 1
    saveinithistory = 1

    # logging
    #pidfile = /var/run/oscam.pid
    logfile = /var/log/oscam.log
    usrfile = /var/log/oscamuser.log
    cwlogdir = /var/log/cw.log
    maxlogsize = 1000

    [monitor]
    port = 988
    monlevel = 4
    nocrypt = 127.0.0.1

    [webif]
    httpport = 10001
    httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255

    [newcamd]
    Key = 0102030405060708091011121314
    Port = 34000@093E:000000


    [dvbapi]
    enabled = 1
    boxtype = dreambox
    user = localuser
    au = 1
    request_mode = 0


    -----------------------------------------------------------


    oscam.server



    [reader]
    label = viasat
    protocol = mouse
    device = /dev/ttyUSB0
    caid = 093E
    boxid = xxxxxxxx
    detect = cd
    mhz = 357
    ident = 093E:000000
    group = 1
    blockemm-u = 0
    blockemm-s = 0
    blockemm-g = 1
    blockemm-unknown = 1


    -----------------------------------------------------------


    oscam.user


    [account]
    user = localuser
    group = 1
    uniq = 0
    monlevel = 0
    au = viasat
    caid = 093E
    ident = 093E:000000
    group = 1



    ---------------------------------------------------------------


    oscam.dvbapi


    P: 093E:000000 # prioritise CAID 0100 with provider 123456


    #P: :093E # prioritise ECM with provider ID 1234 on
    # on any CAID and service


    P: 093E # prioritise CAID 0200


    #P: 093E:000000 # prioritise CAID 0300 on service 9ABC only


    #M: 093E 093E:000000 # map CAID 0400 to provider ID 123456 with
    # CAID 0500


    #D: 0600 200 # wait 200 ms before writing CW for CAID 0600


    #I: :654321 # ignore provider ID 654321 for every CAID and
    # service


    I: 0 # ignore every CAID that was not handled before


    #L: 0700 8e # ECM length for CAID 0700 to 8e (hexadecimal)

    Found this on another site. Hope it helps


    So you want to use the Viasat 016 NDS3 093e card with your Dreambox? Tired of all bull and assumptions you find on the internet? It took a long time for me to make this work and I want to share this info with you all interested. If it is not working for you, than you know for sure you are close to a solution.


    I assume that you can install the cams yourself. ALL the figuration files needed are included in this docuement. Just cut and paste and replace the installed files with my settings.


    I do not assume that all of my settings are perfect, but this is a working configuration, so if you want to make improvements, be my guest.


    You ONLY need oscam.server, oscam.user, oscam.config, mg_cfg and newcamd.list


    I can confirm that my setup is working 100% and also cardsharing perfectly through mgcamd and cccam 2.13. Changing channels going very fast as it should be.


    My setup: DM800se clone, smargo cardreader (buy ORIGINAL) bought from satboy.com, gemini3 version 17 from RamiMaher, cccam213, oscam 1.00 and mgcamd 1.47.


    Firstly, do not start testing my setup WITHOUT a smargo cardreader. Some people have destroyed their cards by using the internal cardreader. It's said that the voltage from the internal reader is too high (5.5 volts). I can not confirm this.


    So it will probably not work without a smargo reader. After you bought the smargo reader you configure it first in your windows computer. You put it in the dreambox-mode and my version is 1.4.
    Get yourself the files to configure the smargo reader. Do here some research yourself!


    You need to figure out your boxid. You need the STB Id code from your original box. This calculation is the ONLY right one for the 093e card:

    Example STB ID: 001058808326 you Discard the first "0" in the beginning and also discard the last digit,and so we will have 105880832----convert it and you will have 64F9D00 which becomes 064F9D00 and thats it,thats our boxkey


    Now, lets start with installing Oscam 1.00 and mgcamd 1.47. Furthermore you can install cccam 2.13 and the config files.


    My operative system is the Gemini3 firmware from Rami Maher, version 17. I can not confirm it will work with all firmware, but Gemini3 is working fine. I installed the TS panel 3 from Tunisiasat and found there all the cams I neededed (Gemini3 cams).


    After installing your cams and config files needed, cut & paste the files to your dreambox and remove the old info.


    The oscam files will be in /etc/tuxbox/config/


    The newcamd.list and mg_cfg will be in /usr/key/
    I was a little unsure if this destination or these 2 files were right so I put another copy of these files in the same folder as the oscam files.


    --------------------------------------------------------------
    oscam.config


    [global]
    usrfile = /emu/log/oscamuser.log
    logfile = /var/log/oscam.log
    disablelog = 0
    disableuserfile = 1
    fallbacktimeout = 2500
    Nice = -10
    WaitForCards = 1
    PreferLocalCards = 1
    saveinithistory = 1


    # logging
    #pidfile = /var/run/oscam.pid
    logfile = /var/log/oscam.log
    usrfile = /var/log/oscamuser.log
    cwlogdir = /var/log/cw.log
    maxlogsize = 1000


    [monitor]
    # port = 988
    # monlevel = 4
    # nocrypt = 127.0.0.1


    [webif]
    httpport = 8888
    httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255


    [newcamd]
    Key = 0102030405060708091011121314
    Port = 34000@093E:000000


    [dvbapi]
    enabled = 0


    #### Check that dvdapi is turned off!!!


    --------------------------------------------------------------
    oscam.server


    Smargo (mousemode)
    # Set enable to 1 if connected to the box, 0 if not used
    #--------------------------------------------------------
    [reader]
    label = smargo
    protocol = mouse
    detect = cd
    device = /dev/ttyUSB0
    enable = 1
    group = 1
    emmcache = 1,3,2
    boxid = XXXXXXXX #here your boxid, 8 digits, remove this text.
    caid = 093E
    mhz = 357
    cardmhz = 357
    blockemm-g = 1


    --------------------------------------------------------------
    oscam.user


    [account]
    user = localuser
    group = 1
    uniq = 0
    monlevel = 0
    au = viasat
    caid = 093E
    #ident = 093E:000000
    group = 1


    [account]
    user = oscamuser
    pwd = oscampass
    description = for local mgcamd
    group = 1,2,3
    au = 1
    --------------------------------------------------------------
    newcamd.list


    CWS_KEEPALIVE = 300
    CWS_INCOMING_PORT = 12000


    CWS = 127.0.0.1 34000 oscamuser oscampass 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan local
    --------------------------------------------------------------
    mg_cfg


    # EMM messages
    M: { 01 }


    # ECM messages
    C: { 01 }


    # AU
    A: { 01 }


    # key update (sum 01 or 02 with 04)
    U: { 05 }


    # config files folder (softcam, autoroll, ignore/priority)


    T: { 00 }


    # network mode, use summ for several clients
    G: { 01 }


    # network retry, use summ for several options
    N: { 07 } 5 30


    # network ecm timeout in seconds
    K: { 05 }


    # newcamd dead routes connect retry, sec
    Q: { 600 }


    # network shares priority
    P: { 00 }


    # on screen display type
    O: { 00 } username password


    # on screen display Options, summ of:
    S: { 03 } 80


    # Log option, summ of:
    L: { 00 }


    # keep ecm cache, seconds
    E: { 15 }


    # cache option, summ of:
    H: { 07 }


    # reread files, summ of:
    R: { 04 }


    # debug, summ of
    D: { 00 }


    # box type
    B: { 02 }


    --------------------------------------------------------------
    cccam.cfg


    # Add this line to your cccam.cfg.


    N: 127.0.0.1 34000 oscamuser oscampass 01 02 03 04 05 06 07 08 09 10 11 12 13 14 256


    keep also all your other lines in this file.
    --------------------------------------------------------------


    Now, please some attention now!


    You run a combination of cccam213 and oscam. This mode should be after installation of the cams in your cam settings of your box.

    ----> CCcam_2.1.3_oscam_1.00_cam.


    If it starts up correctly you can open the oscam interface in your internet browser by writing the ip number of the box and the port. example: 102.168.0.50:8888


    Good luck!


    scansat, september 2011

    • Official Post

    I have added the configuration given above into the correct files for you to try, you will definately need to convert the boxkey to clear all channels.


    You could also try these working configs for 093E cards, How to : Oscam Server or Cardreader with CCcam2.1.3 Viasat Latvia.

    Thanx mate.
    Now, for some other questions, will this work with a 93f card just by changing the caid?
    I seem to have problems with locating a newcamd 1.47, i only have 1.35a, is that okay?
    Ahhh, forgot, is the Smargo Smartreader Plus okay for this project??


    Okay, i am slowly waking up here, the Smargo is to replace the internal cardreader, so no need to buy one, offcourse only if the DB500 does not burn of the cards.
    So, do we just skip this part, because if not, then i have to get another box.

    Got it all up and working, except no picture.
    It might have something to do with the boxid is only 11 digits, Any idears?


    Here's a snip of the logfile



    2012/07/25 18:30:42 300162A0 s version=1.00-unstable_svn, build #4066, system=powerpc-tuxbox-linux, nice=-10
    2012/07/25 18:30:42 300162A0 s client max. idle=120 sec, debug level=0
    2012/07/25 18:30:42 300162A0 s max. logsize=1000 Kb
    2012/07/25 18:30:42 300162A0 s client timeout=5000 ms, fallback timeout=2500 ms, cache delay=0 ms
    2012/07/25 18:30:42 300162A0 s auth size=4800
    2012/07/25 18:30:42 300162A0 s services reloaded: 0 services freed, 2 services loaded
    2012/07/25 18:30:42 300162A0 s userdb reloaded: 0 accounts freed, 1 accounts loaded, 0 expired, 0 disabled
    2012/07/25 18:30:42 300162A0 s signal handling initialized (type=sysv)
    2012/07/25 18:30:42 300162A0 s 775 service-id's loaded
    2012/07/25 18:30:42 300162A0 s 3 tier-id's loaded
    2012/07/25 18:30:42 300162A0 s 4 provid's loaded
    2012/07/25 18:30:42 300162A0 s 1 lengths for caid guessing loaded
    2012/07/25 18:30:42 300162A0 s monitor: disabled
    2012/07/25 18:30:42 300162A0 s camd33: disabled
    2012/07/25 18:30:42 300162A0 s camd35: disabled
    2012/07/25 18:30:42 300162A0 s cs378x: disabled
    2012/07/25 18:30:42 300162A0 s newcamd: initialized (fd=9, port=34000, crypted)
    2012/07/25 18:30:42 300162A0 s CAID: 093E
    2012/07/25 18:30:42 300162A0 s provid #0: 000000
    2012/07/25 18:30:42 300162A0 s cccam: disabled
    2012/07/25 18:30:42 300162A0 s radegast: disabled
    2012/07/25 18:30:42 300162A0 s http thread started
    2012/07/25 18:30:42 300162A0 s creating thread for device /dev/sci0 slot 0
    2012/07/25 18:30:42 300162A0 s waiting for local card init
    2012/07/25 18:30:42 30859B50 h HTTP Server listening on port 8888
    2012/07/25 18:30:42 31059B50 r reader thread started (thread=31059B50, label=viasat, device=/dev/sci0, detect=cd, mhz=357, cardmhz=357)
    2012/07/25 18:30:42 31059B50 r viasat card detected
    2012/07/25 18:30:42 31059B50 r Extra delay for PPC box between reset and IO_Serial_Read for the ATR
    2012/07/25 18:30:43 31059B50 r ATR: 3F 7D 11 25 02 41 B0 03 69 FF 4A 50 F0 80 00 56 54 03
    2012/07/25 18:30:44 31059B50 r Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] parental lock setting: FF FF FF FF
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] type: VideoGuard Viasat (093E), caid: 093E
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] serial: 5F66ACF0, BoxID: *My Box ID*, baseyear: 2000
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] ready for requests
    2012/07/25 18:30:46 31059B50 r found cardsystem
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] viasat card detected
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] type: VideoGuard Viasat (093E)
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 0014, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 0015, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 0016, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 0017, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 0018, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 0019, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 001a, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 001d, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 0021, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 0025, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 0026, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 0027, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 0028, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 0029, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 002b, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 0033, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 0038, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 0039, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 003b, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 003c, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:46 31059B50 r [videoguard2-reader] tier: 003e, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 0043, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 0044, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 0055, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 0056, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 0057, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 0058, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 0059, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 005a, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 005b, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 0065, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 0069, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 006a, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 006b, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 006c, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 006f, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 008e, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 0092, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00a6, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00b3, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00b4, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00b5, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00cd, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00cf, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00dc, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00dd, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00de, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00df, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00e3, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00e4, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00e5, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00e7, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00eb, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00ec, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00ed, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00ee, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00f6, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00fb, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:47 31059B50 r [videoguard2-reader] tier: 00fe, expiry date: 2012/09/17-00:00:00
    2012/07/25 18:30:48 31059B50 r [videoguard2-reader] tier: 0110, expiry date: 2012/09/08-00:00:00
    2012/07/25 18:30:48 31059B50 r [videoguard2-reader] tier: 0118, expiry date: 2012/09/08-00:00:00
    2012/07/25 18:30:48 31059B50 r [videoguard2-reader] tier: 011f, expiry date: 2012/09/08-00:00:00
    2012/07/25 18:30:48 31059B50 r [videoguard2-reader] tier: 0122, expiry date: 2012/09/08-00:00:00
    2012/07/25 18:30:48 31059B50 r [videoguard2-reader] tier: 012a, expiry date: 2012/09/08-00:00:00
    2012/07/25 18:30:48 31059B50 r [videoguard2-reader] tier: 012b, expiry date: 2012/09/08-00:00:00
    2012/07/25 18:30:48 31059B50 r [videoguard2-reader] tier: 012c, expiry date: 2012/09/08-00:00:00
    2012/07/25 18:30:48 31059B50 r [videoguard2-reader] tier: 0131, expiry date: 2012/09/08-00:00:00
    2012/07/25 18:30:48 31059B50 r [videoguard2-reader] tier: 0139, expiry date: 2012/09/08-00:00:00
    2012/07/25 18:30:48 300162A0 s init for all local cards done
    2012/07/25 18:30:48 300162A0 s anti cascading disabled

  • master G

    Set the Label from Viasat OSCam to Nagra Cards OSCam

OSCam Support Forum

Configs, discussion, downloads and guides for OSCam Softcam.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login