Sly Uk not updating

There are 40 replies in this Thread which was already clicked 5,225 times. The last Post () by master G.

    My sly uk card is not updating in my debian linux with smargo reader


    here is my file


    am I missing something


    [reader]
    label = ***_uk
    protocol = smartreader
    enable = 1
    device = 003:002
    caid = 0963
    ident = 0963:000000
    mhz = 600
    cardmhz = 600
    group = 1
    emmcache = 1,3,2
    #smargopatch= 1
    blockemm-u = 0
    blockemm-s = 1
    blockemm-g = 1
    blockemm-unknown= 1
    lb_weight = 101
    ecmwhitelist = 0963@000000:3E,42,44,45,47,4E,53,54,61,62,68,69,6A,6B,6D,6F,71,72,73,77,78,79,7A,7C,7D,7E,80$

    Sorry to bring up my old post but my card still aint updating in server, is there something I need to put my client box?


    I run debian server with omnikey reader (changed recently)


    Client runs mgcamd(tm500s) or newcamd (spiderbox)


    Any help would be greatfully appreciated


    Regards


    Chris

    • Official Post

    When using omnikey instead of smargo you will have to edit the protocol and device, i also enabled shared EMMs which you were blocking.


    Check oscam webinfo or logs for further errors.




    How to : Oscam Server or Cardreader with CCcam2.1.3 S*Y UK IPK

    this is my file used with omnikey reader. updates ok



    label = ***uk
    enable = 1
    protocol = pcsc
    device = 0
    caid = 0963:000000
    # 0963 is *** UK.
    boxid = ********
    # Oscam can read a *** card i.d, but you can also put this
    # in manually
    detect = cd
    cardmhz = 357
    #mhz=686
    # this helps the card run more smootly
    group = 1
    # Oscam has the concept of groups. Only users in group 1 can
    # use this reader. I'm only using one group.
    emmcache = 1,1,2
    ecmcache = 1
    blockemm-unknown = 1
    blockemm-g = 1
    # these ensure smooth decrypting
    #lb_weight = 101
    # for load balancing - can be commented out.


    I thought you might have had to have blockemm s and u disabled to update sly 0963 cards but your setup is blocking s emm dude and i would also remove blockemm-u 0 from your config.


    I would have thought summit like this as an example below would allow emms to update your card but if you want to add blockemm s in try it as below with boxid which was missing from your config.


    Edited example only from your setup but i could be wrong.



    [reader]
    label = ***_uk
    protocol = smartreader
    enable = 1
    device = 003:002
    caid = 0963
    ident = 0963:000000
    boxid = xxxxxxxx
    group = 1
    emmcache = 1,1,0
    smargopatch = 1
    blockemm-g = 1
    blockemm-unknown = 1
    lb_weight = 101
    ecmwhitelist = 0963@000000:3E,4E,4F,42,44,45,47,53,54,56,61,62,6A,6B,6D,6E,6F,67,68,69,7A,7C,7D,7E,71,72,73,74,76,77,78,79,80,8B


    I actually block everything tbh but each to thier own,add your real boxid if you want or leave with xxxxxxxx if you are using a recent oscam which i assume you are with your smargo.


    Also i just bang a 1 in on users to au with my tring card but thats another thing you might wanna look at is your mg_cfg


    Ps whats that dollar sign doing at the end of your ecm whitelist...never seen that b4?

    Quote from romman

    Ps whats that dollar sign doing at the end of your ecm whitelist...never seen that b4?


    Thats just from when I copied and pasted I was logged in via ssh when I copied and thats what there but if I move cursor along it goes



    Quote from Ten Below

    Be sure you are allowing AU from your receiver, generally entitlements on your provider stay at least 6 weeks ahead.


    How can I be sure this is what I have in .user


    [account]
    user = 8888
    pwd = 8888
    group = 1
    uniq = 1
    au = ***_uk
    caid = 0963
    ident = 0963:000000



    this is example of line on tm500s
    CWS = mickey.disney.net 19000 mickey mouse 01 02 03 04 05 06 07 08 09 10 11 12 13 14 wan newcs


    Are the correct or should I add or change anything


    Regards


    Chris

    [account]
    user = mickey
    pwd = mouse
    group = 1
    au = 1
    caid = 0963
    ident = 0963:000000
    cccignorereshare = 0
    keepalive = 1


    This should au in the usergroup you stated


    ie


    CWS = mickey.disney.net 19000 mickey mouse 01 02 03 04 05 06 07 08 09 10 11 12 13 14 wan cardserver (if using an external client to update emms)


    or


    CWS = 127.0.0.1 19000 mickey mouse 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserver (if using home box as server/client to update)


    CWS = 192.168.?.? 19000 mickey mouse 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserver (if using another internal box in your home)

    Quote from Ten Below

    Try using newcamd to connect your local receiver instead, make sure au is enabled in the user account.


    Not sure what you mean mate.


    i am running a tower Debian server.


    I have a tm500 super and a Spiderbox in the house connecting to it


    Cheers
    Chris

    • Official Post


    Like this,
    in oscam conf add or edit.


    Code
    [newcamd]
port                          = 10000@0963:000000
key                           = 0102030405060708091011121314


    in oscam user add or edit


    Code
    [account]
user                          = spiderbox
pwd                           = spiderpass
description                   = for local mgcamd or DVBAPI
group                         = 1
uniq                          = 1
caid                          = 0963
au = [COLOR=#00ff00]reader name[/COLOR]



    Here put your reader label in oscam.server



    And this nline to your spider


    N: IP-Of_Debain_Server 10000 spiderbox spiderpass 01 02 03 04 05 06 07 08 09 10 11 12 13 14 256



    E.G 192.168.1.61

OSCam Support Forum

Configs, discussion, downloads and guides for OSCam Softcam.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login