Posts by master G

Quote from dixiedean

no they didnt come on, basically it had a nabilosat image with the early version of oscam 40 something build and that kept going off randomly, anyone know why this is? so i put your image on with flashwizard and once it was done and before i manually restarted the box the channels all start working , then arter i reboot i dont get nothing no matter how long i wait
and when i check on the oscam webinterface its coming up with an error the theres no reader, so ive flashed back to nablosat which works but as i say every now and again once to twice a day i have to restart oscam as it randomly stops

Is this a story or a question related to this image ?

Quote from fergyc

Ah okay and if I have my peers in oscam.server and oscam.user I remove them from CCcam? bit of a stupid question but just want to make sure.

I think you have a lot of reading to do fergyc, if you are using oscam & cccam then c&f lines belong in cccam.cfg
beer10

Quote from bj1

is this image compatable for tm500...bj1

No, just DM500

You can use oscam as the card reader and CCcam 2.1.3 will be the server for your clients.

Or you can use CCcam protocol in oscam and add all you clients there.

Quote from fergyc

When putting my Sly boxkey into OSCAM is it the same as the one I put into CCcam or is it the numerical one I need?

Also, do I just add the N Line in CCcam.cfg and wipe everything else or keep the boxkey in there too?

As Master G said it is not required, to answer your question yes it is the same boxkey but you must enter it differently

In cccam
BOXKEY: /dev/X 12345678

X = reader

In Oscam
BoxID = 12 34 56 78

The only difference is the spacing.

Quote from madbriuk

i have scanned 28.2E mate

Quote from madbriuk

they have gone again

Quote from madbriuk

maual scan

Did it really need 3 posts to say one sentence lol.

Now you have rescanned the satellite use the compare services option in dreambox edit or just remove & replace both channels using the remote editing function.

Remove the boxkey from CCcam.cfg and add the n line.

Boxkey is not needed in oscam, if theres a line in oscam.server called Boxid, just # or remove it and oscam will read the boxkey automatically.

Look in the Enigma1 channel list section, there are a few recent lists.

You can try a manual scan on the below transponders or upload an Enigma1 channel list.

boomerang 1 - 12051.00, 27500, 2/3 , V

Eurosport1 - 12285.00, 27500, 2/3, V

All transponder frequencies can be found KingOfSat - European Satellite Zapping & Directory

Use dreamset to read the bouquets from the receiver and edit/delete what you dont need then write the bouquets back to the receiver again.

I would not advise you to use CCcam to share this card, it wont block the killer EMM.

Use oscam, it will block killer EMM and you dont need to convert your boxkey.

Are you managing to watch on your own receiver via your new server?

Quote from kieper11

Hi,
Since today i get this error on CCcam control center when i try to connect to my Vu duo......What error is this and how to solve it?thx

I have not heard of that error so its probably a message generated by the programme itself. Give this a try and see if the problem still exists, it will do everything control center does and loads more.

CS Studio by Damirsat ( CCcam Info )

Quote from dixiedean

once i reboot box i lose my channels, its as tho oscam stops reading card

Do they come back soon after ?

Quote

NOTE: 30 seconds after boot both cams are restarted with oscam starting first, this is to eliminate any problems with oscam not finding card reader.

I tested this thoroughly.

In response to private messages

All passwords & ports all default

Dreambox
User = root
Pass = dreambox

Oscam Web Info
To use enter in web browser

http://[COLOR='#FF0000']ip_of_dreambox:8888[/COLOR]/

e.g 192.168.0.3

User = admin
Pass = admin

If anyone has problems with flashwizardpro below is the backup in .img format for use with dreamup ( thanks mtv1 for testing )

This thread is open for a short time only for questions directly related to this backup, anything else will be deleted immediately.

Thanks
Ten Below

Quote from wizzy

ok, the reader shows the entitlements. the lines were made with ccam line manager e.g C: wizzy.dyndns.org 55555 below 10 F: below 10 0 0 0 { 0:0:1 }
I only have flines for clients in cccamcfg, do I need to put them somewhere else?? Something in my head is telling me i need to put 1 fline somewhere else, sure I read it somewhere

This will allow them to view your local only with no reshare, if they are using a pc server or have
minimum downhops 1
enabled in their own box cccam.cfg this will explain why they cannot see your card.
Change it to 0 0 0 { 0:0:2 } and ask your peer if they can now see the card.

CCcam 2.0.11 is the best version to use with Mgcamd, all other versions of CCcam have this freezing problem.

Thanks for the kind words, appreciate that beer10

Quote from wizzy

hi,
it was the auto install tutorial from here http://linuxsat-support.com/li…-installation-ubuntu.html .Listen port is open, static ip set. In server tab it shows one card although the entitlements tab shows nothing. The flines have been copy n pasted from the cfg file in my dm500 which I have been using as my server.In cccam server I can see clients who are connected to me.

This is good it means the card is being read by oscam

To check entitlements in oscam

In your web browser type

http://[COLOR='#FF0000']Ip_Of_Server[/COLOR]:8888/

E.G 192.168.0.9

Click Readers

Then view entitlements

How have you made the flines
e.g F user password 2 0 0 { 0:0:2 } { } { } peers dns

You can see the card in cccam info but your clients see 0 cards, is this correct ?
If yes how are you making your flines.