Merci , mais 7.3 est la minimum.....
Ont elles réellement existées avant la 7.3 pour cette box 4k ?
Car pour d'autres boites cela remonte jusqu'à la 4.0...
TS
Posts by toysoft
-
-
-
Sky italia not working stream relay?
You need iCam table for SKY IT as well as the K1 pairing unique key for your card to your original box,... lot of things not available,
TS
-
Toysoft is it possible you send me the latest timeshift.py or autotines just the file that organize the timeshift. I use 8xstar. Maybe you have the new one
You have here all the source code used by 8.xStar,
Codehttps://github.com/Toysoft/enigma2_0924TS
-
They will reply you that they dont' support DM900UHD... best would be to not talk about the "unofficial" version / box, or use one of the boxes they have on their supported list... choose for example as "your receiver", a VU+ Uno 4k, or VU+ Solo 4k, VU+ Zero 4k etc... that are all UHD... and don't mention after "Dreambox"...
TS
Display MoreI posted this on openpli forum
I have been experiencing ongoing issues with timeshift on my Dreambox UHD 900 running OpenPLi. The problem seems to occur specifically with HEVC/4K channels, such as ESPN UHD. What I notice:
- During timeshift, two files are normally created (for example timeshift.* and .sc).
- However, as soon as I zap away from an HEVC/4K channel, an .ap file consistently remains in the /media/hdd/ folder.
- This does not happen with HD (H.264) channels; only with HEVC/4K.
- After watching an HEVC/4K channel, the stuttering and timeshift issues begin, even when switching to other channels later.
What I have tried so far:
- Increased the delete speed in the recording settings,
- Adjusted the delete options (e.g., set to “everywhere”),
- Using an SSD as storage (which works perfectly otherwise),
- Tested various settings related to timeshift and recordings.
It seems that the Dreambox does not properly clean up the .ap files after stopping timeshift or zapping from HEVC/4K channels, which eventually affects the overall stability of the system.
My question to the forum:
Is this a known issue for others? Are there any updates, patches, or known solutions that specifically address the leftover .ap files with HEVC/4K channels? Any help or suggestions are greatly appreciated!
-
Toy soft i found this..
Timeshift.py need to be change with this code
if filename.startswith("timeshift") and not filename.endswith(".sc") and not filename.endswith(".del") and not filename.endswith(".copy") and not filename.endswith(".ap"):
It's related to the source official code of openpli, we do 100% compatible original image for these boxes, so this needs to be modified on the openpli team source (for all their boxes).
TS
-
It’s the feature that lets me rewind while watching live TV. It activates after 2 seconds. I’ve also set it to 30 seconds before, but the issue keeps coming back. After I disable the feature and change channels again, the stuttering disappears
Is your HDD properly recognized with openpli ? Do you have the timeshift folder ?
TS
-
Dear toysoft
Unfortunately, I am having problems with timeshift. The picture starts stuttering out of nowhere. After restarting the Dreambox, the issue disappears. I have purchased an SSD to improve performance and added extra cooling for my box. I have checked everything thoroughly. Unfortunately, the problem persists whenever I use timeshift, but when I turn timeshift off, everything works fine. Can you help me?
Do you have the same problem with OpenATV ?
TS
-
Code
Let me report, I managed to solve it, the problem was in the computer and laptop it seems. That was my last option if something was wrong. Today at work I formatted the USB and downloaded the image, inserted it into the rec and raised it to 7.4, later made a flash online to 7.5.1 and everything works without problems. I don't understand what caused the problems. If anyone has any advice or guesses what it could be I'm very interested.. So the problem is probably in formatting the USB or I drank some kind of virus on both computers.Yes, most probably the formatting done previously wasn't recognized by the file system supported on the Flashing process of the old VU+ HD boxes.
You done fine, which size was your USB Stick, as this could be also a problem (if greater than 4 Gb if I remember well)... but you used in both tried the same, just reformatted when it was successful.
TS
-
Trouble. I flashed the original release-dm7020hd-3.2.0.nfi for testing without errors. The box also does not boot, it is stuck on the boot logo. I did a full reset to factory settings in the BIOS. It did not help. Where in the forum can I read about recovery?
Capacitors, if you have such problem there is 3 big capacitors to change on the motherboard. I had one box with that problem, freezing... check them if they have an hill on top of them, the ones near to the smartcard reader (right of it watching box from the frontpanel).
TS
-
I can't get OpenWebIF working. Has anyone else this working?
Yes perfectly working... but when you use bad plugins, it will always corrupt things.
TS
-
You have all on the support forum,
Codehttp://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=367#Post367TS
-
does this software also exist for japhar sim dreambox 500 hd identical same
with this the Ncam 15.2 works perfect
Just replace the SSL when you flash the image (flash after the Japhar SSL), and boot the box and replace the bcm7405.ko driver file, and it will work on the DM500HD with Japhar Sim.
TS
-
Try without the option,
--no-check-certificate
or just download the installer.sh into your /tmp folder and run the command from there,
TS
-
Try these if you are not able to do it successully, via the frontpanel button (which works, but it's difficult),
1) First Method
to-the-rescue
or
2) Second Method
echo "rescue" >> /proc/stb/fp/boot_mode
reboot
TS
-
Press frontpanel button, when you turn on the box (1 second after turning it on) and keep the finger there, generally I keep it there on the 50% right of the button until it flashes telling you are now in rescue mode,
TS
-
Display More
yes, I know that.
just someone to tell me how to remove the last plugin, because seems in time when "installing" this plugin have a problem for space--> in telnet - I see that only 600k is in root :)
So i want to try FIRST:
- just all dependencies for last installed plugin to be removed - with "grep" i don't see this plugin installed.
But before that I see I have enough space and all running well.
Best regards...
You have more chances reinstalling the image... than trying to remove a broken installation of a plugin, if it did also dependencies, which could not work as well with the plugin...
TS
-
BIOS is with default settings.
I have no longer the Multiboot or the last one.
I reflash all with new SIM.
The Box booted, but not entirely - seems can't completed boot - telnet and ftp is ok.
The image is Openpli V12.3 - with updated channels ...
You have to flash the image with the sim compatible with the image, this one is for original, so you need to use the original image.
If you want to "port the image" to another sim, generally you need to replace for the sim you want to use the SSL + driver (bcm7405.ko in driver folder) for that sim and it should work.
TS
-
Just reset the BIOS, you can do it easily via the menu, when the box is in Flash mode, you just go with Telnet and flash the BIOS to default parameters.
Once this is done, then it will start booting from the Flash.
Remove all devices (USB and HDD etc) from ports.
TS
-
Display More
Grade image! :)))
One little Question I have - about USB drivers:
- must install some specific drivers to recognize direct the one SSD SATA that is connected to USB port with a USB Case?
Of course in Ext.SATA port works or in DM ONE, in computer works too.
The SSD only blink, but it's not recognized from system when attached in USB Port.
Disk ist: SATA III - Intenso.
Any idea will be very Wellcome! :)))
How is it powered ? Generally the problem is that the external device (HDD) doesn't get enough Amp to work, if it flashes it often shows it tries but fails to read/continue the reading process.
TS
