Posts by abu baniaz

  • Cron job in vix

    There is no benefit whatsoever in using CrossEPG downloader at 04:00. Even Sky receivers stay asleep until after 6:00


    Setup power timers to send box to go to deep sleep after inactivity. Make it wake up 10 minutes before you normally use it. EPG data is normally 7 days, so you should have EPG datat for today anyway.

  • software update

    This command will list the updates for you

    Code
    opkg update && opkg list upgradable


    010 should be out soon. When it is out, make a settings backup, flash 010, and then restore your settings and plugins. This should bypass the issue. You will be on latest image without the issue.

  • HW ERROR on led screen

    it was suggested you flash the image again. you keep saying you are using the image.




    Just try flashing original image again.Also try flashing most recent image.




    Sent from my HTC One M9PLUS using Forum Fiend v1.3.3.

  • ultimo 4k tuners

    To make full use of a uni-cable LNB, you will need a splitter. With a normal LNB, you cannot split the signal, with unicable you can. The number of channels determines how many receivers/(physical tuners) you can use. They do not have to be FBC tuners.


    Unicable LNBs have 4 channels. So you can have 1 signal wire from LNB to first landing. Connect to Splitter 1.
    One wire from splitter 1 to room 1 and connect to splitter 2. Two wires from splitter 2 to both tuners of receiver. E.g TM Nano 3T.
    One wire from splitter 1 to room 2 and connect to splitter 3. Two wires from splitter 3 to both tuners of receiver. E.g Mutant 2400


    All 4 tuners would need to be set for the a specific channel. An example of channels below.


    Output IF Channel 1 (SCR0) 1210 MHz
    Output IF Channel 2 (SCR1) 1420 MHz
    Output IF Channel 3 (SCR2) 1680 MHz
    Output IF Channel 4 (SCR3) 2040 MHz


    Unicable 2 LNBs allow up to 32 channels. There are a few on Amazon. In my view they should really alter their site and have an entry/description for number of channels. This lack of description has led to some sellers describing as quad/quattro. This is wrong. Retail websites should really fix this.


    There are a few brands. All will use a 40mm collar. If you are using a sky dish, you may need an adapter as recent dishes use 38mm.


    If you have two FBC tuners, they are still two tuners. Yes you can access more frequencies. It is important to note that they are still two tuners. Otherwsie, if physical tuners A&B are used and you try to run CrossEPG downloader, it will not run because there is no free tuner. If you assume that you have more than two tuners, that understanding will cause issues.


    FBC tuners basically allow for more internal loopthrough. They do not need a unicable LNB (although that adds more options). To explain, on a normal LNB and one tuner. If you record BBC1 HD, you cannot record ITV 1 HD. (I am using the London region in this example.) However, you can do this with an FBC tuner.

  • Best image for VM epg to work?

    If you are downloading Rytec's EPG data, you have to advise him of the problem, his username is "Doglover". You will have to provide him the service references of the affected channels. He is very good at updating these once people give him the details. He is more active on PLI forum.




    Using EPG from the signal wire is an independent process




    Sent from my HTC One M9PLUS using Forum Fiend v1.3.3.

  • should i reboot box

    The {00} means it should not be logging.
    The IP address being there should not matter. You can try removing its, no harm in trying.


    Sorry about previous post, mg_cfg was auto-corrected to my_cfg

  • should i reboot box

    You are probably using an mg_cfg file that has logging enabled. Mgcamd tries to send logs to the address in the mg_cfg. Your network is flooded and internet stops working.



    Using Notepad ++ or any Linux compatible editor(not Windows Notepad), change the L : {03} to L : {00} You can delete the IP address too if you want. This will resolve the internet issue for you and you won't need to reboot.



    Most of the configs on this forum have 00. I've never tried the ones with 02 ( log to console).



    Sent from my HTC One M9PLUS using Forum Fiend v1.3.3.

  • Thanks to view attachments

    Quote from eastwood

    In my opinion the requirement to thank before downloading should be removed.
    It makes the popular downloads look ridiculous, with nearly a full page of thanks behind a post.


    You do not have to make a post to say thank you to download. You have to click the blue button to " thank for this post".

  • AutoBouquets LraiZer error token ''091''?

    All that has been done in the latest version is to add a check/response if you are on a cable service before continuing and the the GUI changes. Some people failed to read the bit about run the plugin while on a cable service.


    Try the previous version and see if that works.