Posts by abu baniaz

Sorry, I don't understand your responses fully.

Just to repeat/rephrase what I said earlier, tuner configuration for each tuner must match the hardware connected to each tuner.

Tuner configuration must match the hardware. You have told the receiver that you have one type of hardware, but in reality you have something different. If you have not got the same hardware connected to Tuner B as what is connected to Tuner A, you must not tell receiver it is equal to tuner A.

Please explain fully what dish/LNB/diseqc hardware you have. Draw a picture of it is easier. Guessing and assuming could be wrong.

You will not receive all transponders on 28.2e because of where you are.

Where are you located?

Please also make use of the screenshot function instead of taking pictures. There is a link in my signature

Edit:

Screenshot guide here

Thread

[How-To] Take A Screenshot On Any Enigma2 Receiver

Telnet

Use this command (screenshot will be found in /tmp folder):
grab -o -p /tmp/grab.png [change grab to the file name you want it to be] shows OSD only.
grab -d -p /tmp/grab.png [change grab to the file name you want it to be] shows OSD with channel.

OpenWebif Plugin:

Start OpenWebif > Box Control > Grab screenshot
This will load a picture into the main window.

1) right click this image. Save As. Save them to your computer.
2) right click this image. Copy image.. then paste into a graphics…

master G

Mar 13th 2016

Please confirm:

You have two LNBs. One points to Astra 28.2e and one points to badr 26e. You have two diseqc switches. Two wires from each LNB to both diseqc switches. Two signal wires from both diseqc switches to both tuners?

Is the above the hardware that you have? If not please describe fully. Draw a rough sketch if needed.

That is the scanning option. Please post screenshots of your tuner configuration. Please do both A and B.

Do you have signal wires to both tuners A and B

What type of LNB do you have? What is the tuner set as?

When you install items from the plugin server, you are only offered items that are compatible with the the receiver.

Life is too short to waste on rant/rumbling threads. Good luck in your quest.

You are missing the point. It is built to run with the libraries already on your receiver. There are no dependencies included. If any are needed, they will be installed from the plugin server.

All you had to do with the ipks I uploaded was transfer and install the arm version. (Maybe I should not have uploaded the mips one in this thread. I did so because of the rant nature of your posts suggesting there is an issue with the image). Even if you transferred both, opkg would not install the wrong architecture.

If you are going to use a softcam package that someone is uploading, start with a clean image ( i.e no restores), install the ipk as it is provided by the uploader. Start the oscam by command line and report back the error to the compiler . I would suggest you send a message in a succint manner. Less is more! I am sure that they will work out what needs to be done to get it to work.

If you are unzipping the ipk and maually transferring the binary, you could be avoiding any checks/links the installation process has been programmed to do to avoid issues. It is not easy to make the ipks for multiple images.

Those are not by me. In any case, symlinks should have been sufficient.

Please find attached ipks for oscam-emu 2.24.09-11824 version built for ViX 6.6 environment

Where did I provide files? Please post a link so I can edit it to remove confusion. If I did, it was a long time ago and the files are likely to be incompatible with the current version of ViX.

The simplest option for the OP is to install oscam compiled to run on vix 6.6

What page of mine? Please apply the KISS protocol.

6.6 images use a different OE branch. Maybe the person compiling the packages you are using has not updated the build environment they are using. Start oscam by command line and it should tell you what the issue is.

The Vu kexec multiboot is only for the Vu 4K receivers. So won't work on the Solo SE

You have not said which image is in flash. OpenMultiBoot seldom works with PLI in flash. You are better off installing ATV/VIX in flash memory. Then install openmultiboot plugin from the plugin server.

If you don't get an answer, might be an idea to contact the manufacturer directly.

ZGEMMA H17COMBO

1、Broadcom BCM7251S 2、DDR3 1GB 3、eMMC:16GB 4、Tuner: DVB-C/T2 + S2X 5、Build-in Wifi: 300M 6、CI+: *1 support 7、CA ：*1 support 8、USB2.0*1+USB3.0*1 support…

www.zgemma.org

The SE has more internal flash and more RAM. It is a better receiver. The receiver is a hardware multiboot receiver. You can't do anything about it. However, flash one image in one slot/partition.

"recovery_emmc" images are flashed by USB

"multi images" are flashed by remote/online

You can also boot in the recovery image and flash from there. You must have an ethernet cable to be able to download an image.

Try booting into OpenPLi and then flash ATV from there. Flash into the same partition as PLI as you want to overwrite it.

Quote from Nikos200

Hello friends, I've recently been trying to install the whitelist but it doesn't work. Can someone explain the correct way step by step?
I have a VU+ UNO 4K SE with OpenPli 7.3. or where can I find a current sky de icam settings list. Thanks

Waste of time you doing this, it won't work. For PLI, the stream relay functionality has not been added to the Release image. It will be added in release 9.1. You can use the developer image which has the functionality though. If you want to stay on your current image, you will have to use a modified set of bouquets.

If it is a recent ( roughly last 3 years) image from one of the OE-A teams (Open ATV etc) you will need to set a password before you can FTP.

You are mixing up terms. Bouquets= Groups of channels. EPG = Synopsis. ABM just does bouquets, it does nothing with EPG.

Best you set ABM after 0600. Once a week on Thursday is fine for most people.

If you want to manually optain the OpenTV EPG, there is an option in the blue button/extensions menu. Blue > Force OpenTV EPG download.

Are you talking about bouquets or EPG?

If EPG, how are you obtaining EPG?

Which version of ViX are you on?