even in usals, sometimes (for unknown reason) the receiver takes like wrong the coordinates.
for example, in the past, in my motor... i am living to 21 degrees, but i had to set the receiver to 25 degrees to be in the "center" of all satellites...
the only thing youu can do is this. go in the dish settings, and try to change (but always remember what is now, to re-set it in this again if nothing changes) the longitude...
How I can change the dish settings in the receiver?
Display Morei think snr 60% is not quite enough signal. i think that you can receive strong beams/frequencies, and not the not so strong...
i think you need to adjust better your dish ,
as i remember you have got a motor, so ...(simple or usals?)
or the installation (the dish) needs the adjustment,
or your receiver needs better setup, to adjust the dish...
and no the other frequencies will not be affected, signal will be better and to them.and... in a perfect dish setup, all satellites should be in a "line" and none of them could loose signal
Oh thanks, I am using usals so I can't adjust it. How I can adjust the motor through the program?
What signals strength that it need to do better?
I will tell the satellite company to adjust it for me as I have already paid it.
maybe yes...
in a frequency that you are receiving, what the signal bar shows?
SNR: 60%
AGC: 85%
BER: 0%
If I have to get him to adjust it, will it not affect the frequencies for the other countries like Germany, italy, Poland...etc?
Unzip and replace this satellite.xml file. Path is etc / tuxbox.
It make no different as I have tried it.
I think I have found the issue. When I check for the Netherlands channels like fox sports 1, the frequency is 11739. I have check on 11739 V and there is no signals. Do you know what I need to do?
Do I need to contact satellite company to adjust the dish on the wall?
Why would you clean before you scan?
Look, use a good list, like CIefp's, then additionally scan.... but DO NOT CLEAN before you scan!
Well I need to do for a fresh start like start all over again.
What you mean by use a good list like Clefp's?
How I can do that on openatv??
Thanks for the help guys. I have select on manual scan -> single satellite -> 23.5east astra3b -> network scan -> yes -> clean scan -> yes so when I pressed on scan button, I'm getting Skylink / M7 Group - Czechoslovak and Telekom Srbija - Serbian satellite provider on hotbird 23.5 East. There are only 204 channels. No Netherlands channels are display on the list.
Any idea??
Sorry I use octagon sf8008.
Display MoreClick on the "Custom" tab from the top, then select which satellites you use.
Upload the .xml file then restart the box.
Start the scan again.
I have downloaded and upload satellite.xml and restarted the box but when I rescan it using automatic scan it make no different. Any idea??
Thanks for your help.
Are there any files I need to delete before I rescan it again?
Update the satellites.xml file in etc/enigma2
Thanks for the quick reply.
Do I need to select ku-band or c-band only? Or do I need to select both?
When I download it, how I can stop the service running on openatv?
Do I just upload the xml if it would not affect satellite.xml?
Hi all,
I need your help. I have got a problem with searching for the satellite channels. When I use automatic search to search for the channels on hotbird 7 East, 9 East, 13 East, 16 East, 19 East, 23.5 East, 39 East, alot of sports and other channels did not show up on the search list especially sport klub 1, 2, 3 serbia, play sports 1,2, canal sports 1,2,3,4 poland, sky sports 1 and 2 italy, idman tv, Cosomote sport...etc.
And alot of Netherlands channels did not show up on the search for the hotbird 23.5 East as well. It will only show Czech Republic channels and some Croatia channels.
I am using 80cm dish it have got a very strong signals and I am also using the motor to change the hotbird. I am using openatv 6.4 image.
Do you know why the channels doesn't show up on the automatic search?
Does it got blocked or do I need to update the xml file?
Any advice would be much appreciated.
Thanks in advance.
He explained that it depends on the house and position of the dish, as well as how far do you want to drive the dish...
Bigger usually is better... More flexibility, to move the dish left/right...
Oh right. I can only get 80cm dish as I have permission to put on the wall and I can't get more than that.
Do I need to get a mesh dish or a solid dish??
I am thinking to get between 40cm and 80cm wall mount to allow the dish to have more room when I move it to the left and right. If you can advice me what size I need to get that would be very helpful.
Is black mount good or this one is good??
And do I need 40cm or 80cm wall mount??
Yeah but the things is it don't have weather restrictions and it won't last as it will cause rusts. So this is why I want a black one to prevent it rusts.
Display Moreyour new motorised dish will move some way right and some way left
if you have no space from wall to the dish
WHERE WILL THE DISH HIT and not move
think about it
Oh right, so is 40cm not good enough as I need 80cm wall mount? Is that correct?
If so where I can find a black mount with 80cm length??
I have found these but the one I like is 40cm black brackets. Is the 40cm bracket good enough to fit for a 80cm dish? Yes or no?
The one I like is the original one like sky UK mini dish as the bracket have weather restrictions to stop it rusts.
Thanks for the help guys, I have decided to get a motor.
Do you know how big the mount I need to get to put on a wall and that would fit a 80cm dish?
Is 40cm bracket good enough to fit for a 80cm dish??
Oh ok I got it now. Thank you very much for your help as this is all I need to know for now.
