Display Moreo I need to get 3 lnbs?
each lnb needs to be tweaked to point at the preferred satellite
you need a multi lnb setup
yes you need a separate lnb for each satellite
Oh I got it.
Can you show me an example picture what does the multi lnb setup looks like?
Can I install 4 lbns on a single dish??
Will it works if I install the dish lower ground on my back garden??
not 13-16-19.2 in 80cm
, for a reason that i explained above (imagine something like "audi" logo, a circle in a part of circle). you need 1m dish , 4 lnbs , and a 4/1 diseqc switch. but you do not refer your area (because a few satellites has special beams etc...)
Oh right. Thats too big for me to get 1m dish. I could get 90cm to put it in the back garden. Will that works?
I am from Dover in kent.
a quad lnb, does not provide you 4 different satellites, but 4 lines in the same satellite (for different rooms, or same room pvr receiver etc...)
depends your area (an important think) , you can do it, but you need 1m plus size dish, not for signal strength, but because the triple 13-16-19.2 is too close, and every lnb need its "area" .
also, the satellite 16E is called eutelsat 16E and not hotbird...
Oh I thought that a quad lnb does provide me 4 different satellite so I got it wrong.
So how I can get 4 different satellites on a 80cm dish using with a single dish cable?
do I need to get 3 lnbs?
16 has a weak signal. receiving it will depend how big your dish is. bigger the dish - better chance of receiving signal.
you can`t view any footy from this satellite. its all encrypted.
Well I am planning to get 80cm dish to put it on the wall, but if my landlord dont allow me then I will get 90cm dish to put it in the back garden.
Can I ask you that if I get quad lnb to put it on the dish with 4 different hotbirds (19.2e, 23.5e, 13e, 16e) on a single lnb when I point at 13E?
Will that works?
That`s true you can get 19.2 & 23.5 with multi lnb if you point at 13. But it doesn`t provide all the channels for footy. You may get signal, but they are premium channels.
What about can I get quad lnb to receive 4 different hotbirds (19.2e, 23.5e, 13e, 16e) on a single lnb when I point at 13E?
Like this:
Display Morethere are pages, like flysat, lyngsat and kingofsat, where you can see what channels contains any satellite...
but, first of all .
Quote
I want to know in what hotbird do I need to point my dish to the sky so I can get full european channels?hotbird is just a name. other name, is astra. near the name, is the satellite position (astra 19,2E , astra 28.2E , hotbird 13E)
in any case
1) you can't receive all those channels in one satellite. you need to receive more satellites, so 1 dish and motor,
or more dishes, more lnb etc...
2) most channels which shows premier league, are encrypted and need subscription (legal or not...) .
anyway, you can check the link that master G gave and try to do a list with channels that may be intersting for you. than check their satellite (and sometimes a footprint check could be usefull).
Thanks for your suggests. I understand where you are coming from now as it does make sense.
I might need 3 lnbs but not sure if i do need to. I want to get astra 19.2E, astra 28.e2, hotbird 13E, hotbird, 16E.
Do you know how many lnbs do I need?
watching 3 pm footy is not as straight forward now as you may think mate.
one satellite doesn`t have all the channels that broadcast the games.
you would need a motorized dish. even then its no guarantee the game will be available ~ https://liveonsat.com/quickindex.html
if you have a good internet connection consider iptv instead, no dish required.
Thanks for your reply.
Do you mean i need to move the dish to change the hotbird?
I'm thinking about to get the dish to point it to hotbird 13E, but can I get full holland, germany and spain channels as well?
Hi all,
I need your help. I want to know in what hotbird do I need to point my dish to the sky so I can get full european channels?
I want to get full european channels for portugal, france, germany, italy, spain, hungrian, romania, croatia, serbia...etc. I want to get the full european channels so I can choose what channels I want to watch for the premier league. I'm planning to get 80cm which it should be enough to get full european channels, but if I dont have planning permission from the landlord to put the dish on the wall I would get 90cm dish to put it in the back garden beside my shed so no one would see it.
Any advice would be much appreciated.
Thanks in advance.
will it works for wetek play 2??
I know how to get into recovery mode but I dont know what to do after I pressed on the upgrade button take take me to the recovery mode.
I've attached the picture for you to take a look.
Please let me know what option I should go with so I'll try again.
P.S Im new to this and never done this before.
Do you know what I need to do???
What do I need to do?
I dont have a clue what to do as you sent me the link and I dont know where to start.
I have read it and it didnt say anything how to boot the micro sd card on wetek play 2. It will only take me to recovery mode.
How i can boot it?
Hi all,
I need your help. I have a bit of trouble with booting with my sd card, when I pressed the upgrade button on the back of the wetek play 2 for 7 seconds, it will take me to go to recovery mode so it won't boot. I've checked on the sd card on the file manager and it can read the sd card with no problem.
How do you get the openelec to boot when you press on the upgrade button?
Are there anything that I might have miss something?
What I did is I have copied the files of .zip, .alm and img from the zip file that I downloaded and I've pasted them onto my sd card.
Any advice would be much appreciated.
Thanks in advance.
Oh what a shame. what about ccam? will it works??
Hi all,
I have got some questions. Are there any of you have been successfully using oscam to get access to sky uk channels such as sports and movies?
If so, I would love to know how do you get access it.
Thanks in advance.
Why have you posted details for a Vu+ duo ? Which receiver do you have ?
If it`s a duo you have, you can`t transcode with this receiver, you need a solo2, duo2 or solo 4k..
Maybe this plugin will sort the password -> Dreambox Password cracker/resetter Enigma2
I only have duo reciever so that means i cant transcode on this receiver? should i get rid of this receiver and get solo2?
can i be able to download the plugin online to change the password?
Hi guys
I need your help. I want to change the password on dreambox, I can get access to the dreambox via putty, but it would not let me to connect to the dreambox as it have close the putty app so I cant be able to change the password. It sound like to me the port is closed or blocked.
Do you know what app or what plugin I could use to allow me to change/reset the password?
And for other issue, I have a problem with the stream as it would not let me to watch the live tv on my pc. I tried to enable zap before stream but I still get the same problem. I don't think I have transcoding plugin on the dreambox to allow the stream to work. Can you help me with that please??
Do you know where I can find the plugin for the password change/reset and also do you know where i can find the transcoding plugin?
Here is the screenshot where you can see:
Here's the details for my dreambox:
Brand: Vu+
Model: Duo
Chipset: 7335
Frontprocessor Version: 0
Total Memory: 131348 kB
Free Memory: 32948 kB
Box Uptime: 14:09
Software
System OE: OE-Alliance 3.3
Distro: openvix
Firmware version: 4.0.003
Driver date: 20151124
Kernel version: 3.9.6
Gui version: 2016-03-23
Tuners
Tuner A: BCM7335 DVB-S2 NIM (internal) (DVB-S2)
Tuner B: BCM7335 DVB-S2 NIM (internal) (DVB-S2)
Thanks in advance
It sounds like you need to setup a password in telnet to allow an FTP connection.. Are you able to get a telnet connection ? If so, try changing the password by typing passwd then pressing enter, follow on screen instruction. You could check on the images addons / plugin feed for a password changer..
can i be able to set up a password in my dreambox screen? if so how i can do that then?
i can't set up a password in telnet because i am outside of the network. i can however login using the ip. can you tell me how i can set up a password in the telnet using the ip?
I have tried it but it won't let me to connect to the dreambox. I guess that there is no way to connect to a dreambox without knowing the username and password.
By the way, I have found a way to control the dreambox through on the internet. When I set the enable http authentication to yes and when i saved, it will let me to connect to the dreambox without require the username and password.
Do you know how it will get me to require the username and password when I set the enable http authentication to yes?
