Posts by abdul.jabbar

fresh install. started again …

does this image not support open vpn ?

does someone have the answer or suggest another image with open vpn

after a fresh install from the open pli site I deleted plugins that I do not use or do not know. I may have deleted something that contains the open vpn

I could just flash image again and start from the beginning but would be nice to know which plugin I need to install from the menu

hi,

i have an open pli 7.2 image on a vuplus solo2 box

i am trying to install ipvanish

i am following guide and got to a place where i need to set open vpn but cannot find it.

menu/setup/system/expert settings/network does not show me OpenVPN .

i have tried menu/plugins/download plugins and tried both in system plugins and extensions but cannot find this

any ideas .

Quote from abu baniaz

Menu, plugins, green (download), system plugins,

Select CrossEPG, confirm installation

thanks mate , that worked … I must be going mad I was convinced I tried this

Quote from abu baniaz

Which exact image do you have? Version and date please. You don't need to download any ipks

open pli 7.2 2/3/2020

thanks for replying . the receiver is a vuplus solo2

I have installed the sat venus panel … and tried to install cross epg this way still no luck

I have download from this site .ipk file and tried via software manager … still no good

also tried slyk epg 7 day set to London .. click the yellow button to download .. starts to show status changeing so something is happening thaen receiver crashes with green screen and reboots

and using openpli image .. menu/plugins/down load plugins .. does not have cross epg

hi, need help woth cross epg

I have latest openpli image but cannot install cross epg .

can some one point me to the correct version for this image . Thanks

Quote from Panda555

Tar.gz file open with WINRaR, and only transfer files with DCConnect in your box.Just follow in which file it goes on.

THanks mate , worked

Hi,

i have E2i player installed on my vusolo2 box

it has stopped updating .. i can see Esiplayer uploaded .... is this a newer version

I know how to install .ipk files by sending to temp using dccconect and installing by plugins/software management/install local extesion but how do i install the .tar or is this not for vusolo?

using autobouquets E2 plugin I have noticed the same . instead of international try the the sky box office tab. all Asian channels are in there.

Hi,

any installers in the Watford area . I need installing a motorised dish

I have concreted in a pole . I can take coax and signal wires to dish

I have a vu solo2 box

alsat v3000 vbox

langsa track motor . this looks like a huge disec

a dish

need the above connecting and setting up

thanks

I still have a simple list how do change this to a list showing all . Thanks

after a recent update to media portal I have lost the porn channels . all I get is a simple list.

if I press epg on the remote I get enter adult pin. previously this was 0000

This no longer works . any ideas

File

MediaPortal E2

MediaPortal Enigma2 Plugin allows you to play different web spaces.

W@Rp

Jul 26th 2021

Hi

same as before seems to install ok ie no error messages . on restart the reciever boots too quickly . There are no signs of the plugin
Now tspannel has the update but installing from this get error message python-six and python-cfscrape
Heve tried instally python-cfscrape but have same problems with installing this as installing the medaiportal pluginn

I thing i will flas box again with new image and try from the start .. Thanks

In telnet i did not get any error messages . it looks like the depency install without any problems. but after a restart when you go to plugins an error no module named cfscrape shows
I have now removed media portal . added the dependancy you suggested in your link and than reinstall media portal fromts pannel ( version 7.5.8)

When i run media portal it shows an update is available ... during update it says version 7.5.5 being updated to 7.6.0 which is strange as i have just installed 7.5.8 from tspannel

Now update is not succesfull and get a message medaiportal update unsuccesful Chech the update log carefully

but this time i still have the old version medai portal

Hi

After the latest update a few days ago i get a message no module named cfscrape

I have tried http://linuxsat-support.com/sh…portal-Arm-type-receivers posted by master G and also
python-cfscrape_1.6.6-r0_all.ipk but no luck

THe reciever is a vu plus solo2 running open pli

I opened the box and made sure tuner is seated . also gave it a good clean
I also found an inline signal booster and connected this
did the scan as before but no channels

up until now I had disabled the terresial ans sat part of the tuner so this time enabled the satellite and tried scanning sat channels . this worked fine so also tried using the satellite part while connected to the cable feed
but still no good...

before buying a new tuner can someone upload the dm800se clone (sunray .. the one with mini flashup button on the back) trial tuner drivers
maybe the drivers I have are not correct even though they show the 3 in one ie cable ,sat,terresial

skunk1111 .
if you have the same box ie dm800se the image would be great. even if it is for a different box upload backup as it may help someone

Inspiral

never tried Terrestrial but satellite was fine until recently were certain frequencies started to show failed tune and sometimes the fav list on the non working channels greyed out.
a retune would normally fix this for a while. last time I tried on satellite I reflashed image and sat chennels were fine . but for how long I do not know.
so may be the tuner after getting hot started to play up

I have tried leaving all tuner options as standard and also disabled the Terresial and satellite only enabling the cable

I have also now confimed my cable connection with some borrowed cable boxes and the free channels do work . ealier I must have tried a non working cable box along with the dm800se satellite finder where I saw no signal hence my issues

I think I will search for a cable tuner ... THanks for all your hel

Inspiral Hi

Thanks once again for replying
I managed to find the PLi-4 gjstroom and flashed box

I added the cable.xml and autobouquets for cable

Tuner Config mode = enabled yes
Net Id = (set this for your area ok) eg mines = 00010 yes mine is 41051
Used Service Scan Type = Provider yes
Provider to Scan = V***** M**** yes
now hit Green Button to save yes

this takes you back to tuner page showing the 3 tuners . I exit / select cable scan/

on this page theses are the default settings

tuner tuner c:trialtuner DVB -C (BVB-C)
frequency 323
symbol rate 6875
modulation QAM64
network id 00000
use official channel numbering no
hd list no
enable auto cable scan yes

I press ok to scan and quite quickly I get failed scanning failed

I than exit and go back to the same page and change the network id in this page to my network id of 4105 and try again still the same

I have also tried the automatic scan. this show a progess bar and goes from 0 to 100 but no channels
I have also tried the manual scan and selected complte as type of scan . this also shows a progress bar but still no channels

I can only assume the 3in one tune is crap

I could either buy a separate cable tuner and try again or buy another box say a zgemma what would you recommend

I did manage to find my old subbed vi..media box and got some free channels on that so there must be some signal .. may be low
strangely I could not get any signal even the free channels on my old modded (talk back disable box) .. I would have thought that the free channels should have worked ..
I will try again later

Hi
Thanks for the autobouquets file
installed , changed attributes etc

when I go to plugins and click ok on file there is no option to press menu and set any preferences . it simply starts to run but only for a few seconds.
its too quick to get the complete error message but its something to the effect ....... cant open file at line x no file exits

in etc /tuxbox there is a satellite,xml shouls there a cable .xml if so where can I get a copy

I have edited the file with my network id on line 9
with autobouquets I have a favorites list ie sports but the folder itself is empty , this is the same for all the favorites