problem solved with plugins "ts-sateditor"
Posts by viper82
-
-
do a netscan from the satelite
ok, yes, but can't manually enter a known frequency?
-
wanting to manually add a frequency directly from the decoder how should I do?
( I am not referring to the procedure to take the " satellites.xml " file via ftp with the pc and modify it, but if there is a plugin that directly from the decoder gives the possibility to add new frequencies and save them. )
-
7°E
11180 / H / 7200 / FEC: 3/4
ID: Snooker Tour Championship 2023
CW: please?
-
viper82 , as asked what was the problem please share information because some other members may one day have same problem and that
is for me whole point of a forum to just say problem solved personaly is does not help considering the good members on here that did try to help.
The problem encountered was the very very heavy dish, the motor was unable to maintain the correct weight and position for effective pointing, removing the heavy 100 dish by inserting a much much lighter 80 dish the problem was solved
-
What was the problem?
The problem encountered was the very very heavy dish, the motor was unable to maintain the correct weight and position for effective pointing, removing the heavy 100 dish by inserting a much much lighter 80 dish the problem was solved
-
7E
11080 - Pol: H - SR: 9874
ID: D514 M08 Main
Biss please?Biss2
???
-
Problem solved, thank you all for your support
N.B. The problem encountered was the very very heavy dish, the motor was unable to maintain the correct weight and position for effective pointing, removing the heavy 100 dish by inserting a much much lighter 80 dish the problem was solved.
I sincerely thank all those who have helped and supported me in the smallest details on this adventure
-
Eutelsat 7B - 7C (7.0°E)
Fréquence: 12522 - Pol: V - SR: 7500 - FEC: -
CW PLEASE
-
how can you explain the fact that with a 100 dish the signal was poor and with an 80 dish the signal is excellent?
-
With a dish of 80 cm the signals are excellent. When you mounted the 100 cm dish, did you place it exactly in the same place with the same elevation angle as with the 80 dish. Try to move the 100 dish a little left and right, but only a little to get a better signal. Also, with a dish of 80, search for some other satellites such as 0.8 W, 7W, 28.2 E, 42E and some further east. Is your engine tilt angle and antenna elevation the same as in the instructions (engine tilt angle 40.5 and elevation 49.5) or some other.
Everything remained the same, I just removed the 100 dish from the engine and inserted the 80cm one, nothing else.
What has been done is:
1) engine go to 0
2) removed 100 dish from the engine
3) added 80 dish to the engine
4) engine go to 16e
end.
Everything else remained unchanged,
motor not touched, motor lnb connection cable not replaced, lnb not replaced.
( I can't check the signal because there is a lot of wind, so any value would be incorrect. )
Quick check on satellites:
0.8W 12034 4! STORY TV SNR: 78/80 AGC:99 BER:0
7W 12015 2M MONDE SNR: 44 AGC:90 BER:270
28.2 E 11464 AASTHA TV INTER, SNR: 92 AGC:99 BER:0
42E 11999 A PARA HD SNR: 91 AGC:99 BER:0
Tomorrow will be an excellent day with no wind, I will be able to perfect the signal, but right now it is already a significant step forward compared to the 100cm dish.
-
1) 100cm dish installation. Many attempts have been made, the following value is the maximum I was able to obtain.
(the following value refers to 6km/h wind conditions)
2) 80cm dish installation. The following value refers to the first installation carried out with an 80cm motorized dish, (The only difference between a 100cm motorized dish installation and an 80cm dish installation is the replacement of the dish, all the rest is that of installing the 100cm dish)
(the following value refers to 24km/h wind conditions)
Why is there this notable difference?
I repeat that all the material used for the 100cm motorized dish was used for the 80cm motorized dish.
A considerable gain even at 30w where with a 100cm dish the signal was fluctuating or absent, in the 80cm dish the signal is modest and fixed.
N.B. Right now the wind is 24 km/h so the signal isn't fixed, I'll have to go back to fix the signal properly.
-
You must know one thing. For now, it is not possible to open skyit via streamrelay, except for those few channels, and I explained why that is so. Rare providers (clines) have a 09CD card, and even those who have it, the question is whether it would work (good and bad sides of the law). Even if you buy a line the question is whether you will be able to watch skyit at all. Unfortunately, we have to be patient and see how the situation around skyit will develop further. Here isn't problem with oscam icam and streamrelay , because both it works well for skyde
and skyuk ( partially for skyuk )
what are the few channels you see (skit)?
-
what do you mean by "4:2:2" ?
https://en.wikipedia.org/wiki/Chroma_subsampling#4:2:2
in few words is a transmission type that cannot be decoded by the majority of consumer's devices (i know it's not the correct definitation but just to give the idea that is usually for professional uses)
anyway the feed you reporter is black because they are not transmitting any video
A thousand thanks ( when it is 4:2:2 it can be seen from PC? )
-
what do you mean by "4:2:2" ?
-
19E
11618 H 9874
ID: FIN-029 SKI JUMP
NEW CW PLEASE --> E1 8F BD 2D 23 03 24 4A
19E
11604 H 9874
ID: FIN-029 CC
NEW CW PLEASE ---> NO SIGNAL
19E
11.406 V 22000
ID: MM2 Service 4
NEW CW PLEASE --> E1 4F FD 2D 23 03 24 4A
it should be 4:2:2
????
-
19E
11618 H 9874
ID: FIN-029 SKI JUMP
NEW CW PLEASE --> E1 8F BD 2D 23 03 24 4A
19E
11604 H 9874
ID: FIN-029 CC
NEW CW PLEASE ---> NO SIGNAL
19E
11.406 V 22000
ID: MM2 Service 4
NEW CW PLEASE --> E1 4F FD 2D 23 03 24 4A
-
does anyone know how to set up stream relay ? keep trying the steps but getting black screen
did you read what was written in the previous posts, and also what I wrote regarding this problem you are having right now?
-
Have you maxed the signal? Are you getting the coverage, you want?
i'm trying to maximize the signal
-
How do you extract a k1 key from the official card?
great question, many of us are waiting for the answer