Your quality of signals are good , but must be better on 16 E. Try to up elevation of your dish and check frequency 11554 V 30000.
This frequency is the strongest on this satellite. Signal must be near 100% , with my dish 85 is about 97 - 99 %.
now is snr: 78%/80% agc 99%
now is snr: 11.5 db / 11.8 db agc 99%
dish and motor set up on thor 1 west 100% signal quality the wall bracet or ground pool mast bee 100% line up the dish on set up dipend on your location an you will receive all satellite from 50 east to 50 west
I did not understand
If you will have better results or signal with dish 80 cm , do it the same thing with new dish , but we will see tomorow.
I know that you will solved your "problem" with new dish.
I think so too, this 100 dish just bought I don't know why but it has always given problems, mounted on the pole aimed at 13E the maximum signal I could find was 60% maximum 70% with an 80cm dish always mounted on the same pole, same lnb , same cable, the signal is 91%.
With a larger dish, shouldn't it increase and give a better signal? 
... then you could look at your LNB, some makes are better than others.
To change your signal levels to DB -
menu-setup-usage and user interface-settings-show SNR as % instead of DB (not all stb support this function)
ok, what is the use of doing this?
set from % to db
Display MoreThank you. Only few frequencies for each satellite.
Astra 19 E
11538 V 22000
11229 V 22000
11361 H 22000
Eutelsat 16 E
11262 H 30000
11139 V 27500
11554 V 30000
11637 V 30000
Eutelsat 13 E
11766 V 29900
11432 V 29900
10971 H 29700
ok.
Eutelsat 13 E
10971 H 29700 --- SNR: 83/86 AGC: 99 BER: 0
11432 V 29900 --- SNR: 83 AGC: 99 BER: 0
11766 V 29900 --- SNR: 78/80 AGC: 99 BER: 0
Eutelsat 16 E
11139 V 27500 --- SNR: 55/57 AGC: 95 BER: 0
11262 H 30000 --- SNR: 554/55 AGC: 96 BER: 0
11554 V 30000 --- SNR: 70/72 AGC: 99 BER: 0
11637 V 30000 --- SNR: 80 AGC: 99 BER: 0
Astra 19 E
11229 V 22000 --- SNR: 67 AGC: 99 BER: 0
11361 H 22000 --- I don't have this frequency
11362 H 22000 --- SNR: 75 AGC: 99 BER: 0
11538 V 22000 --- SNR: 75 AGC: 99 BER: 0
Display Moreokay that kind of makes sense, it is the sort of thing i would have to see myself, i am still trying to get my head round it.
I keep forgetting the OP is not in the UK.
EDIT
Sorry !!
The more i think about this, the more i am coming to the conclusion that panda and Chris230291 are correct.
As to how much difference it will make actually make, i am not sure, after all the motor is designed to pan the full arc, and the arc never changes.
From the map above then 16east is closest to your due south.
So if your up for messing about with your setup yet again, it would be interesting to see the results.
I will have to buy you a beer for your troubles !!
I've already tried many times (I've been trying for several months) with a setting of 16e set as the starting satellite, but only when I set 0.8w as the starting satellite that I found a significant difference in signal, tomorrow I'll take a 80cm dish because when I mounted the 80cm one I didn't have all these problems I'm having with this 100cm one.
p.s. there is nothing to apologize because what you offered me was advice so there is absolutely nothing to apologize 
as I take the 80cm one tomorrow I will set it up again with the 16e satellite as primary let's see what happens.
all advice is always welcome
Display MoreYour dish isn't yet properly adjusted. Also your signal strength will be different then Jenseneverest who is in UK and you
in southern Italy. I will repeat once more , your central satellit is Eutelsat 16 E and when you find the best signals on some
frequencies ( see my post #39 ) then will be much better for other satellites in your range ( especially 30 W which is also important
for adjust). Why not try ?
After adjustment , what is the current signal strength on 19 , 16 and 13 E now ?
Tell me which frequencies you are interested in knowing about 19,16,13 that I post them
Is the anything blocking your line of sight to some satellites ? a tree or a house ?
yes, houses, the parabola is higher than the houses (you can raise it again if you want) currently from the roof the dish is at a height of 6 meters fixed to a wall approximately 4 meters above.
I am glad things have improved
me too a lot 
but if there trees or buildings in the way then they will need to be removed
Also change your SNR to DB values, they mean far more to me
I did not understand
Display MoreFor comparison this is my signal using my 80cm dish - my line of sight is completely clear
30west
cubavision 10770 h 30000 --- SNR 14.1db
Telesur HD 10939 h 15000 --- SNR 13.1db
27w
BBC one HD 11495 V 44100 --- SNR 13.9db
22w
Canal Algerie 12674 H 20740 ---SNR 11.2db
15w
ESPN 901 12609 H 7552 --- SNR 10.4db
7w
Qatar TV HD 10834 V 27500 --- SNR 7.3db
36e
1 ARKHI 11212 H 14400 ---SNR 10.2db
39e
ERT 1 HD 122224 H 13381 --- SNR 9.9db
BBC WORLD 12242 H 13381 ---SNR 8.9db
4E 10730 H 30000 ---- SNR 14.5db
Prima sport 1 HD 12290 V 30000 --- SNR12.1 db
52e
247Box 11221 V 27500 --- SNR 12.8db
68.5e
POWER TV 12562 H 30000 --- SNR 8.2 db
And a test channel
34.5 WEST
11469 H 14975 ---- 14.3 db
For comparison this is my signal
30west
cubavision 10770 h 30000 --- SNR: 63 AGC: 95 BER: 0
Telesur HD 10939 h 15000 --- SNR: 58 AGC: 82 BER: 0
27w
BBC one HD 11495 V 44100 --- SNR: 0 AGC: 0 BER: 0
22w
Canal Algerie 12674 H 20740 ---SNR: 43 AGC: 79 BER: 0
15w
ESPN 901 12609 H 7552 --- SNR: 50 AGC: 78 BER: 0
7w
Qatar TV HD 10834 V 27500 --- SNR: 0 AGC: 0 BER: 0
Saudi Channel 1 12149 V 27500 --- SNR: 40 AGC: 84 BER: 140/200
36e
1 ARKHI 11212 H 14400 --- SNR: 0/30 AGC: 78 BER: 0/1900 0/630 (Unstable)
39e
ERT 1 HD 122224 H 13381 --- SNR: 44/46/47 AGC: 83 BER: 0
BBC WORLD 12241 H 13381 ---SNR 8.9db SNR: 35/37 AGC: 81/82 BER: 0 (Unstable)
4E 10730 H 30000 ---- SNR: 81 AGC: 98 BER: 0
Prima sport 1 HD 12290 V 30000 --- SNR: 64/66 AGC: 98 BER: 0
52e
247Box 11221 V 27500 --- SNR: 33/35/37 AGC: 83/84 BER: 95/150/ (Unstable)
68.5e
POWER TV 12562 H 30000 --- SNR: 0 AGC: 0 BER: 0
34.5 WEST
11469 H 14975 ---- I could not test because I have no channel list
I know I can fix the signal even better, but how?
for example: on 7E the feeds I can only get (nhl service 1 and nhl service 2)
while the frequencies:
Eutelsat 7A/B ( 7.0°E )
11153 H 7200
11171 V 7199
11149 V 14399
12527 V 4998
11189 V 7198
11171 V 7198
11189 V 7200
12628 H 7199
I don't get them, even if I use blindScan it doesn't find them
Hello everyone, Panda555 is right, normally you have to see the basic setting with your longitude, for example at home for me it was around 6.80 est....so if it corresponds to an existing sat you take it, otherwise you choose closest .... for my part I took the sat turk at 7° east, it was the closest to my exact south ....
why is 16e not the closest satellite to me?
my longitude is 17.
As I wrote in the previous post or left out my longitude and closest satellite and I did as I was advised by (jenseneverest) starting from 0.8w perfecting the satellite from there so currently I have found a significant improvement on the satellites
I doubt it, you are still 20cm smaller than maximum dish size. which is probably another 10kg's in weight.
But if you started on 16e as your Zero point, then dish will be way over to the west when trying to get signal at 30w.
For me the motor should be on 0 when starting close to real due south, which is roughly the 0.8w satellite i suggested you begin with.
(introduction) I started following those who told me to start from the satellite closest to my longitude (16E) (to leave nothing to chance) since I had already started that way, trying to perfect the signal, I then went to 30W no signal, going to 42.0E no signal.
After having done many tests of signal arrangement at the extremes returning to 16e then 13e/ 7e 5w so on saying the signal was not good enough, so I started to follow your advice go to 0.8w which had a signal from 60 to 70% I started them to perfect the signal.
As it was before: 0.8w with frequency (12034.0 MHz V 30000 3/4 8ps 0.8°w) the signal is: snr 67 agc 98 ber 0
Now frequency: (12034.0 MHz V 30000 3/4 8ps 0.8°w) the signal is: snr 80agc 99 ber 0 (noticeable increase in signal)
0.8w
Before: Now:
frequency (11938.0......) snr 80 agc 94 ber 0----------------------------> frequency (11938.0......) snr 95/97 agc 99 ber 0
frequency (10778.0......) snr 0 agc 0 ber 0-------------------------------> frequency (10778.0......) snr 0 agc 0 ber 0
frequency (11996.0......) snr 77 agc 98 ber 0----------------------------> frequency (11996.0......) snr 89 agc 99 ber 0
frequency (12188.0......) snr 70 agc 98 ber 0----------------------------> frequency (12188.0......) snr 89 agc 99 ber 0
frequency (11843.0......) snr 70 agc 97 ber 0----------------------------> frequency (11843.0......) snr 80 agc 99 ber 0
frequency (12188.0......) snr 70/72 agc 98 ber 0------------------------> frequency (12188.0......) snr 87 agc 99 ber 0
frequency (11325.0......) snr 0 agc 0 ber 0--------------------------------> frequency (11325.0......) snr 0 agc 0 ber 0
frequency (10934.0......) snr 0 agc 0 ber 0-------------------------------> frequency (10934.0......) snr 0 agc 0 ber 0
frequency (10903.0......) snr 0 agc 0 ber 0--------------------------------> frequency (10903.0......) snr 0 agc 0 ber 0
frequency (11229.0......) the signal is: snr 0 agc 0 ber 0-------------> frequency (11229.0......) the signal is: snr 0 agc 0 ber 0
frequency (12418.0......) snr 58/63 agc 98 ber 0------------------------> frequency (12418.0......) snr 80 agc 99 ber 0 (noticeable increase in signal)
frequency (12207.0......) snr 70/72 agc 99 ber 0------------------------> frequency (12207.0......) snr 89/91 agc 99 ber 0
frequency (12054.0......) snr 72 agc 98 ber 0-----------------------------> frequency (12054.0......) snr 86 agc 99 ber 0
frequency (11977.0......) snr 66/67 agc 95 ber 0------------------------> frequency (11977.0......) snr 81 agc 99 ber 0
...
30w
Before: Now:
frequency (12360.0......) snr 0 agc 0 ber 0-------------------------------> frequency (12360.0......) snr 54/55 agc 89 ber 0
frequency (10770.0......) snr 0 agc 0 ber 0-------------------------------> frequency (10770.0......) snr 0 agc 0 ber 0 (Cubavision Internacional)
frequency (12476.0......) snr 0 agc 0 ber 0-------------------------------> frequency (12476.0......) snr 0/49 0/52 0/47 agc 90 ber 0 (Amc break)
...
the 30w satellite is not stable.
Doing as you said I have a significant improvement in the satellites. How can I improve everything to have a signal on all satellites?
If you get a signal by pushing the dish to the right, what should you do?
Display MoreYes that is where i always start 0.8w
Reset you motor before setting up again, as if starting from new again.
Motor should then be driven to 0.8w (some motors have digital displays on the actual motor - i am not sure about your one? )
Fine tune for best signal on 0.8w on both H and V transponders try channel U tv (12687 H 27500) and channel Al Jazeera English (12418 V 28000) both are free channels.
Then drive motor to 30west and check for signal ,then to 39 east, and check for signal.
If there is no signal at 30w or 39e then bend dish face up or down to try for signal, that will tell you which way to adjust the motor latitude.
Go back to 0.8 west and check for signal. If signal is reduced, fine tune parabolic (dish face) elevation.
Repeat this process several times, between all 3 satellites' until you have good signal on all 3.
When you do, then you should have good signal everywhere, the full satellite arc.
Ok thanks tomorrow morning I do that Currently if I push the dish up I have 70% signal on 30w and other satellites w. So if I push the dish up what should I do?
As it is set now, going to 0.8w with frequency (12034.0 MHz V 30000 3/4 8psk 0.8°w) the signal is: snr 67 agc 98 ber 0
frequency (11938.0 MHz h 28000 7/8 qpsk 0.8°w) the signal is: snr 80 agc 94 ber 0
frequency (10778.0......) the signal is: snr 0 agc 0 ber 0
frequency (11996.0......) the signal is: snr 77 agc 98 ber 0
frequency (12188.0......) the signal is: snr 70 agc 98 ber 0
frequency (11843.0......) the signal is: snr 70 agc 97 ber 0
frequency (12188.0......) the signal is: snr 70/72 agc 98 ber 0
frequency (11325.0......) the signal is: snr 0 agc 0 ber 0
frequency (10934.0......) the signal is: snr 0 agc 0 ber 0
frequency (10903.0......) the signal is: snr 0 agc 0 ber 0
frequency (11229.0......) the signal is: snr 0 agc 0 ber 0
frequency (12418.0......) the signal is: snr 58/63 agc 98 ber 0
frequency (12207.0......) the signal is: snr 70/72 agc 99 ber 0
frequency (12054.0......) the signal is: snr 72 agc 98 ber 0
frequency (11977.0......) the signal is: snr 66/67 agc 95 ber 0
...
What frequency do you recommend to use for the start?
I doubt it, you are still 20cm smaller than maximum dish size. which is probably another 10kg's in weight.
But if you started on 16e as your Zero point, then dish will be way over to the west when trying to get signal at 30w.
For me the motor should be on 0 when starting close to real due south, which is roughly the 0.8w satellite i suggested you begin with.
so i have to start with 0.8w?
should the motor be at 0 or 0.8w?
example 1: motor at 0 and point the parable at 0.8w?
example 2: motor at 0.8w and point the parabola at 0.8w?
Display MoreDisplay MoreInstallation:
Signals
DAS ERSTE HD 19.2E : signal fluctuates from SNR 87/89%
RTSH 16E: signal fluctuates from SNR 60/63%
RSI LA1 HD 13E : signal fluctuates from SNR 81/83%
RTL HD 9E : signal fluctuates from SNR 78/80%
4U TV HD 7E : signal fluctuates from SNR 78/80%
AUST. COMEDY AND DRAMA 15.0W : signal fluctuates from SNR 33/35%
CUBAVISION INTER 30.0W : signal SNR 0%
I noticed that taking the dish by making a little pressure from left to right the signal is also present at 30W with power 60/70, (by doing this little pressure the motor arm moves) leaving the dish at 30w it does not give a signal.
Could it depend on the weight of the dish that unbalances the motor? (the dish weighs 20kg)
Good post
Others may disagree with me, and i am not a professional satellite installer, only a hobbyist, but i have 3 motorised dishes and have moved house 7 times in 20 years so have done it more than once....
The fact you have 0 signal on 30 west tells me your settings are still way out, 30 West is a strong satellite as well !! I receive good signal with my 80cm dish there
28, 19, 16, 13, 9 east are all strong satellites don not even bother testing on those.
First and foremost make sure your usuals setting on your STB are correct for your long and latitude. Make sure you do not mix up east and west.
You will see i am very close to 0 longitude so if i get east and west wrong i still get signal on some sats!!
The fact you have good signal on some sats means you are not that far out.
What you say about bending the dish face in a certain direction is exactly right and is how you fine tune it.
But you need to that with 3 satellites as far east / west as possible and one in the middle.
That is why i said to use 0.8w - 30w and 39east.
You need to get good signal on all 3 of those sats to give you good signal everywhere else, the full arc.
once you are happy with those 3 sats you can fine tune even more on hard signals, say 21.5 east and 8west.
could it depend on the weight of the dish?
Installation:
Signals
DAS ERSTE HD 19.2E : signal fluctuates from SNR 87/89%
RTSH 16E: signal fluctuates from SNR 60/63%
RSI LA1 HD 13E : signal fluctuates from SNR 81/83%
RTL HD 9E : signal fluctuates from SNR 78/80%
4U TV HD 7E : signal fluctuates from SNR 78/80%
AUST. COMEDY AND DRAMA 15.0W : signal fluctuates from SNR 33/35%
CUBAVISION INTER 30.0W : signal SNR 0%
I noticed that taking the dish by making a little pressure from left to right the signal is also present at 30W with power 60/70, (by doing this little pressure the motor arm moves) leaving the dish at 30w it does not give a signal.
Could it depend on the weight of the dish that unbalances the motor? (the dish weighs 20kg)
Regardless of what satellite you begin with there is very little point to using strong signal for setting up a motorised dish that spans a full arc.
For example in SE UK I can get 16east on my 60cm mesh dish. It is useless to set up on 16e unless you only want one satellite.
I was told that to set up the motorized dish you have to start with the satellite closest to my longitude, my longitude is 17° and therefore my reference satellite will be 16E.
this I was told 
I don't have motorized dish , but I will try to help you. You must adjusted your motorized dish according to the latitude and longitude
of your city or town. According to the longitude of your city , true south is required to adjust the dish. The tilt of the hand ( arm ) of your
satellite motor is the latitude of your city or town. What is your exactly longitude and latitude ? Maybe will help this site.
I've never used that site, I use this site https://www.dishpointer.com/
I have an active skit 09cd card and box for testing if anyone can help me extract k1 and k3 keys.
there are two of us, but apparently those who know hold it tight
Poor alignment
But you need to be using the same LNB and STB to do a comparison
I am also assuming the dish's are in exactly the same place.
Have you got the new dish up now ?
All identical, the only thing different is the satellite dish, same pole perfectly level, same motor, same lnb, with the 100 one the signal on 16 and poor with the 80 one the signal is much better,
there should be no difference right?
