Solo2 + BH203 here
Posts by scouser97
-
-
weird just tried new and still same prob with tuner :(
-
BH 203 here but still no go
-
Just tested on my Solo2 and it knocks out tuner config so put back ipk package :(
-
anyone got cams working ? tried manual install of ipk packages but still no good with cccam v2.3.0
-
I have just been searching for a turorial for my original S*ybox to update the firmware..
I have looked in openbox tutorials & searched for it cannot find.
anyone ??
Hope this helps :)
SETTING UP ***BOX F3 / M3
ATTACH BOX TO POWER, SATELLITE, HDMI AND ROUTER
1: Format your USB into FAT32
2: Drag your downloaded Image file, and if you have them, Channel list and cccam.cfg onto the usb stick.
3: Turn on the openbox and let it boot up.
4: Place USB stick in back of Openbox
5: Using remote, select 'MENU', then 'TOOLS'
6: Select 'Upgrade by USB'
7: Make sure the top line says "Upgrade Mode <Image File(*.abs)" If it doesnt, use right or left arrow key on remote to change it until it does
8: Move down and select the .abs file on your memory stick
9: Move down to start and press 'OK' on remote.
10: Select 'yes' to any questions the box may ask..
11: Once done, the box may reboot
12: Once done rebooting, enter menu again and select 'Single Satellite Scan'
13: On top line select 'Eurobird 1 & Astra'
14: Next line 'FTA Only' select NO
15: SCAN CHANNEL : TV + Radio
16: Scan Mode: Blind Scan
17: Select "search"
18: Once finished scanning, we can set up our clineCLINE SETUP
1: Go back to main menu
2: Select Network
3: Select "CCcam Client Setup"
4: If you have a cccam.cfg on your usb, select 'Update files by usb' if not, jump to number 27
5: On new window, highlight 'CCcam.cfg', press green button on remote (ADD). This will place a tick by it, the press yellow button on remote (READ)
6: Once finished, select 'Manage Config Files' and on new window select cccam.cfg again
7: A new page comes up with your cline on it, press green button on remote to make it active (tick should appear by it) Exit out of all menus to tv and select a pay channel.. it should clear, if not go back into menu, select Network, then 'Network Setup', and turn DHCP 'ON' by using arrow keys and then hitting apply.
8: if channel still doesnt clear, reboot box and router by unplugging both from power and plugging back in (router first)
9: for those who didnt create a cccam.cfg on their usb, you can add it manually..
a] instead of update by usb on ccccam client setup, go directly to Manage Config Files and select CCcam.cfg from new window
b] Press Blue button on remote
c] your cline will look something like this>>> C: example.cline.org 12000 user pass
d] ON add cline window, leave Protocol as CCcam
e] Host: here you would enter example.cline.org portion of your cline using remote number buttons like you was sending a text
f] Port: here you put 12000
g] User, write 'user' here
f: Password, write 'pass' here
g] Press ok and go up to instruction number 7 OF CLINE SETUP -
hi all i'am tring to install tspanel 6.7mips nf ipk and i don't know the commands i read on here that i need to force an overwrite. i've never done this can anyone let me have the commans so that i can try and installn tspanel. i'am using dream elite 4.0 in a sr4 800se a8p sim
thanks bri31here you go m8, make sure the 6.7 mipsel is in the tmp dir in box. Then load up telnet and type this ------> opkg install -force-overwrite /tmp/enigma2-plugin-extensions-tspanel_6.7_mipsel.ipk
-
***box Openbox M3 F3 Satellite receiver
***box usb wifi adaptor dongole
design for ***box M3 ***box F3 openbox x3
Hi there I am new to these kind of receivers and want to know which one of the above will work with my
slyway classic 3 HD receiver? The router/AP is upstairs and the box is downstairs in living room. Without
the internet connection I cannot configure the box and use it to its full capacity. At the moment it is only
showing me FTA and the Non-FTA shows 'scrambled service'. Also if anyone can point me into the right
direction I want to try Enigma2 if there is any newbies step by step guide it will be very help. I got Sly fixed
dish I do not have any right size ladder to make any changes even though I can manage DIY just right.
The box has got updated latest firmware.
http://***wayhd.ru/***way-classic3.htmlApologies to admin if I have open the thread in wrong section, it can be moved if needed.
Thanks in advance
OceansI got top one m8 with box and all works good with no drop out of signal