Never use it... But I guess you are right - I should test and report back, write a little tutorial... ;)
Posts by gorski
-
-
Delfi:
"AutoScan, Manual scan etc. fixed.
Dinobot 4k (and Axas, Izibox, Anadol) drivers updated.
For 6.3 SF8008 on line reflash (or via USB recovery menu) as there is new fmpeg 4.2x (from 3.4x)
For the above (and some other HiSilicon boxes like ax60, viperk4k etc) here is beta Netflix DLOAD" -
-
-
Do you have a CS part functioning or not?
If you do:
1) If you are paying the guy he should help you out, for your money... (I am against that, just to make it clear...)
2) If he is just a friend, then you need to have a friendly chat...
If you do not:
3) Sky DE can not be opened using an emulator unless you have a paid subscription (smartcard in your machine).
4) If you have a paid subscription you must configure properly your local card reader in your OSCam...
For instance:
Code
Display More[reader] label = Oben enabled = 1 protocol = internal device = /dev/sci0 detect = cd mhz = 540 cardmhz = 2700 ident = 0100:000068 group = 1 emmcache = 1,5,15 [reader] label = Unten enabled = 1 protocol = internal device = /dev/sci1 detect = cd boxkey = xxxxxx rsakey = xxxxxx mhz = 450 cardmhz = 2700 ident = 1803:000000 group = 2 emmcache = 1,3,2 -
-
So far so good, with PurE2... :)
Sat TV is OK,
Streaming is OK (Ciefp channel list, with IPTV channels),
YIFY is OK,
playback I still have to check out...
L8r... :)
-
It's simple with plugins, softcams, tools etc. - if you use PurE2:
How to flash H9x/H9.2x series - post no. 21 by me
Simple flashing procedure for H9 COMBO/TWIN image
1) Power off your Combo/Twin at the back, using the white power button.
2) Download and send an unzipped, new Combo/Twin image from your PC to a compatible USB stick.
3) Put the USB stick (with the new image to flash) in either of the 2 Combo/Twin USB slots.
4) Press the white power button at the back and immediately press the OK button on your remote control unit and hold it, until you see "rCUY" on the LED.
5) You will see the Recovery menu > choose what you want to do...
=> "Bootmenu"
=> Flash local image
=> choose USB stick where the image is
=> choose the zipped h9combo.zip"
=> choose the partition to flash it to (Linux 1 - 4 are for Enigma2 images)
=> you will see "Flashing"... wait a bit...
"Flashing completed"...
6) You will now see the main recovery/boot menu again > simply choose which partition you want to boot into...
-
-
-
Find my Sticky in OSCam Emu section re. PV and study it...
But given the link is in this thread (post no. 2) and you missed it (you don't refer to it) - I doubt you will, in which case your provider should help you out, esp. if you are paying the person...
-
Well, did you change the physical switch over to 1.1?
-
It's all easy-peasy in PurE2, no need for any of this... Well, at least for boxes we do have and support...
-
Do you have a physical switch between DiSEqc 1.0., 1.1 and 1.2?
It seems to me you are in 1.0, not in 1.1.
-
Have you tried without messing with ports A, B etc.?
Only the ones I showed need changing?
The order of DiSEqC 1.1, then 1.0, then toneburst is OK. Just don't mess with ports (A, B...)!
-
Yes - but you need DiSEqC 1.1!!!! Look at my post no. 8!!!
No A, B etc.Only change the ones I mentioned and see then!!!
-
Did you set it physically to DiSEqC 1.1? Can we see the image of it?
Once you do that (if you can do that) it should work as I described... -
Zgemma H9 Twin model just arrived and it looks awesome...
It has an HDMI cable and WiFi, too, 2 x CI slots, a card reader, USB 2 port, mSD slot, SATA HDD slot into which one can plug one's HDD without opening the box.
Be careful! Do not insert or remove the HDD while Zgemma H9 Twin is powered up! First switch it off, unplug the electrical cable, then remove the SATA HDD!!!
I have a HGST 500GB HDD 2.5 inch and it fits just fine. I initialised it by the image that is in the machine... Mounted as /media/hdd.
Inserted 16GB USB memory stick (Data Traveller 2.0) formatted by Windows 7 in FAT32 and mounted as /media/usb no problem.
OpenATV 6.2 is in - not muchly interested.... I'll come back when I install PurE2... ;) -
Sorry, I don't have your box... Nor do I have your problem on any of my boxes....
Try Ccache version and see...
-
Do you have a switch on it, to change the protocols from 1.0 to 1.1 and 1.2?
Failing the above:
Codehttps://www.amazon.de/DiseqC-Schalter-EMP-Centauri-mit-Wetterschutzgeh%C3%A4use-P167/dp/B0021CY1AK/ref=sr_1_fkmr2_1?__mk_de_DE=%C3%85M%C3%85%C5%BD%C3%95%C3%91&keywords=CENTAURI+8+IN+1+SWITCH&qid=1571617143&sr=8-1-fkmr2#HLCXComparisonWidget_feature_div
