Posts by dekelster

My cyfra ecm are a little high, around 200ms. Other locals are fine. So trying to reduce this.

Will running the following sudo apt-get update & sudo apt-get upgrade also update the omnikey drivers if there is an update available?

If not, how do I make sure my omnikey drivers are the latest.
Any other ideas on how to reduce that ecm.

Reader for cyfra:

[reader]
label = CYFRA
protocol = pcsc
device = 0
mhz = 357
cardmhz = 357
emmcache = 1,3,2
group = 2
caid = 0100

Recently added the bits shown in blue, doesn't seem to have made any diff tho.
Thanks

I have even noticed friends of friends on Fb advertising 'cheap sly'.

This forum has also seen a huge influx of new members. Not saying this is a bad thing but it certainly makes you think.

Sent from my HTC One X using Tapatalk 2

Do you need:

mhz = 357
cardmhz = 357

I thought for omnikeys this wasn't needed as it auto detected?

I have 3 omnikeys running. Two with caid 0963 (two card with diff entitlements) and the other with cyfra caid.

Am using a diff account for each card.

If you want to see the relevant files I can email them to you.

Try the card in sly box to confirm its not damaged. Or if you box has another slot, try it too.

Also check the entitlements.

Sent from my HTC One X using Tapatalk 2

Good to know. Thanks

XS Usenet - Free Usenet provider

Free
Speed 1Mbit
Data 25GB
Connections 2
Max Hosts 1

Sign up for a free account. Each account has the above limitations.
But if you sign up for multiple accounts using different email address................

I currently have two accounts which both work fine at the same time. I use it as backup and as a filler.

Need to set up my oscam files etc
But thanks to info on here and everyones help, so far so good.

My card is showing up in oscam Webif with entitlements etc :)

Thanks folks

yup, as above when I run that command I get

# Detected readers (pcsc)
Nr. Card Features Name
0 No OmniKey CardMan 3121 00 00
1 Yes OmniKey CardMan 3121 01 00

Replaced my files with the uploaded ones, many thanks btw.
Then restarted pcscd.

Now when I run the command 'opensc-tool -l' I get:

# Detected readers (pcsc)
Nr. Card Features Name
0 Yes OmniKey CardMan 3121 00 00
1 No OmniKey CardMan 3121 01 00

But if I run command ' opensc-tool ?list-readers -i' I get:

opensc 0.12.2 [gcc 4.6.3]
Enabled features: zlib readline openssl pcsc(libpcsclite.so.1)
root@ubuntu:~#

So I take it thats the readers installed ok now?

All these new commands etc are confusing, I have scrap bits of paper everywhere!!
Just not quite ready to switch from win7 to linux.

Will do mate. Thanks.
If no joy I'll post opensc file.

Quote from Ten Below

I set this up last week on Ubuntu as above only edited the lines that were present & it was working well, i also did a fresh install of debian 6.0.5 less than a week ago & in this os the pcsc file is unchanged from the version shown in the omnikey tutorial. If for any reason you end up trying Debian instead this script has been updated.

[h=1]Automated Oscam/CCcam 2.1.3 Install Package For Debian 6[/h]

ok, just to clarify then the only changes made to opensc file are:

remove hash from 'try_emulation_first = yes;'
remove hash from 'lock_login = true;' and change value to false?

When I run opensc-tool ?list-readers -i

I get:

opensc 0.12.2 [gcc 4.6.3]
Enabled features: zlib readline openssl pcsc(libpcsclite.so.1)

thanks

haven't got that far yet. Just trying to install my omnikey and get it to show up when I run the command to list readers. If someone could message or mail me their opensc file so that I can compare.

I did have to change the value here 'lock_login = false;' from true to false & unhash 'provider_library = /lib/libpcsclite.so.1'
So some editing was required?

Has the opensc file been updated?

I am trying to do the following step in ubuntu tut:

And change thise lines by removing # from front and reader_drivers lines u delete one comand too:
reader_drivers = pcsc, ctapi;

But I can't find that line. There seems to be a section for pcsc & ctapi.
Maybe I'm blind!

cheers

This is a nice new thread. Wouldn't want to upset thatfellow ;)

anyways I had posted this at the tail end of his ubuntu tut:

'Having a wee play with this. But when I log into my router I can't see the linux PC. It is also wired to the router.
Do I need to install samba?'

I can now see linux PC on my network :stmutz:

I had to reset my router to factory settings and install new firmware.

Took me about 6 installs of ubuntu to figure what the problem was. But at least I now know what 'sudo' and 'nano' are!

Quote from thatfellow

OK m8, In the tut above I suggested not touching the /etc/network/interfaces and to give the static IP within the router settings.

Your problem is within your hostname & networking settings. Since you assigned your static IP address from within Ubuntu, you have one or the other or both setup incorrectly.

For a quick fix, Revert back to DHCP instead of static within /etc/network/interfaces and set the static IP address within your router.

As this problem is not related to the Auto Install, Please start a new thread for support.

Display More

I would certainly set the static IP address within my router, if indeed the server showed up on my lan as a connected device etc but it doesn't.

I'll change back to DHCP to see if it appears. It was originally set this way and didn't show up.

Sorry for messing your thread btw! I appreciate the tut and if this doesn't resolve it I will start a new thread.

Quote from thatfellow

Thats pretty strange..
1.. Check the cable with your laptop to rule out that.
2.. Was your server connected to the router during Ubuntu Setup & Install? If so, the ethernet card drivers & DHCP settings should have been automatically configured.
3.. Have you made any changes to the networking settings in Ubunty?

The cable is fine. I ran the ifconfig and got the ip address from there. Then I edited the /etc/network/interfaces file to change to a static ip. This also worked and now have a static ip.
Now the sudo apt-get update & upgrade is just throwing up error messages like:

root@ubuntu:~# sudo apt-get update
Err http://gb.archive.ubuntu.com precise InRelease

Err http://gb.archive.ubuntu.com precise-updates InRelease

Err http://gb.archive.ubuntu.com precise-backports InRelease

Err http://security.ubuntu.com precise-security InRelease

Err http://security.ubuntu.com precise-security Release.gpg
Temporary failure resolving âsecurity.ubuntu.comâ
Err http://gb.archive.ubuntu.com precise Release.gpg
Temporary failure resolving âgb.archive.ubuntu.comâ
Err http://gb.archive.ubuntu.com precise-updates Release.gpg
Temporary failure resolving âgb.archive.ubuntu.comâ
Err http://gb.archive.ubuntu.com precise-backports Release.gpg
Temporary failure resolving âgb.archive.ubuntu.comâ
Reading package lists... Done
W: Failed to fetch http://gb.archive.ubuntu.com/ubuntu/dists/precise/InRelease

Any ideas? Think it is a problem stemming from the server not showing up in my router and then access being denied. Can't see any firewall options in my router (netgear wndr3700)

I can access the server via putty though.

Having a wee play with this. But when I log into my router I can't see the linux PC. It is also wired to the router.
Do I need to install samba?

Thanks

I only noticed a problem with astraweb lately. i.e try getting any of the 1st two movies in the batman trilogy.
But I'll check out supernews.

Thanks folks

Anyone recommend a good usenet provider?

Giganews remove HBO stuff pretty quickly and Astraweb starting to having lots of incompletes for me.

I use a a blocknews account for backup.

Cheers