Must be OpenElec CCcam client or server to another?
If it must be the server you need to match the client's C line with your Oscam.config file and oscam user on openElec box
If OpenElec box must be a client of another CCcamserver you can create a new card reader in Oscam and match them with the F line on the server.
I do not know satellites and cards but it may well be that you can receive channels as the map is not open. I can on the satellites I receive. There I get the same message. Card not found.
What happens if you go back to the channel working?
TV2 dk Lorry
QPSK
Symbol :27500000
Vertical
3/4 48
F:12476000
or?
As I see it, it should be possible to say do. I have something similar, but confirm you have followed the rules here, so we can move on.
I had no problems with it.
I was just very disappointed with it and the features.
For example it is very cumbersome to have to set it to the correct remote control and had to remotely control the other end with a viatuel remote. It is also slow and I had the biggest HD model.
If you need dne to steaming a satelite box is much better to buy an Enigma box and control it directly mentioned. In my opinion.
Enter the box's IP address in a browser, navigate around there and use the icon view TV.
If you want to do it from the WAN, you must route the ports in your router, and of course, enter your WAN address in the browser.
I've had a Slingbox HD and was very disappointed. No, it just moves the signal it receives into on the internet, then you should play it in a SlingPlayer. So direct answer, no you should see the same program everywhere.
Purchase a Enigma2 box and steam from it instead. It works much better here and costs less.
Hello again
Sorry the delay, time passed and my PC went down with all sw for dreambox, but I wanted to try today.
This result, the box driving fortunate shown ever
:45:51 PM box is flashing from its memory...
2:45:55 PM Flashing failed (!!! 010 INVALID IMAGE (OR OLD VERSION)), box will be unusable now!!
I think it would be feasible on a Dreambox. I have not tried.
If I were to make one, I would share a USB on the box where it is mounted and mount it as a network drive on the client box.
It might be worth a try if you have the options of your box
But when you know the man who has given you the line should he tell you how to use it and expect it works in his end.
C lines works in CCcam, and be formed to run in Oscam how depends on the other setup so it's not easy.
C line work in CCcam, but if "someone" is a payment servers do not count on help from here. Detailed opposite.
Try a few times and wait a few minutes between attempts. I have experienced the same, or try a different version of DreamUp.
It is also optiflash I think it's called, you can try. My computer went down, so I have no more.
You have mastered the com port in DreamUp?
You're going into the setup through the "blue button" and click around a bit and activate CCcam. It is not always it starts by itself.
Follow this guide. It works as you'd like.
A setup but Oscam as reader and CCcam on the client is easy to set up and works perfectly stable
Unfortunately, the solution is small we really see anything: (
But now I know how it works, but it's bad for your work not be seen properly.
You can easily run oscam and CCcam on the same server, and for example let CCcam download from Oscam, but it's easier to let Oscam run it all and let it emulate CCcam, or rather, use CCcam SERVICE PROTOCOL from Oscam.
Paste this into oscam.conf:
[newcamd]
port = 12XX@0x3x:000000
key = 0102030405060708091011121314
keepalive = 1
mgclient = 1
[cccam]
port = xxxx
version = 2.2.1
reshare = 2
forward_origin_card = 1
FIXED
ADD this to your [global]
[global]
block_same_ip = 0
block_same_name = 0
Tried and it worked immediately. Thank you, but is there someone who can explain what is happening with Oscam when it works locally?
Well it's nice there is a solution to that particular problem, because I have completely the same.
I play with when I get home, but is not what it is for, OscamA or OscamB
[global]
block_same_ip = 0
block_same_name = 0
Must be copied in?
It must have been a big job, but well done :)
Have got it working, thanks for the help.
