Posts by codar

  • Channels are missing from the list

    Do a full scan, then , if there is only a few channels missing, press up - green (select the satellite you scanned) and scroll down to the missing channel, press menu when highlighted and add that service (channel) to your desired bouquet.


    Exit.


    Go to your desired bouquet, scroll down to channel that's not working, when highlighted press menu and remove selected service. Scroll to the bottom of the bouquet and the one that you added earlier should be there, when highlighted press menu and "enable move mode" this will enable you to hold (press ok) and move (using the arrow keys) the selected service up to your desired location within your bouquet. To exit "enable move mode" just hit menu again and select "disable move mode"

  • Which driver for AVermedia A850 DVBT zgemma openvix

    You'll need to know the chipset of it and download the relevant driver from the image feeds.

    You'll probably hit a problem here though as vix don't do an official image for the zgemma so the feeds or driver may not work properly.

    ATV on the other hand do an official image, you may be more successful with it.

  • Any other sub?

    Quote from Nathan.24

    how do I go about having that put onto my box then mate?

    You need genuine receiver for it.

    Quote from ComfySofa

    Ive had a motorised system for ever but not really used it (and less so over the years)... Is there anything worth going to on other sats?

    There's a good variety on 13e and 19e, probably more on other sats too but thats all I've access to atm, until i get my old technomate 2200 motor up n running again.

  • Any other sub?

    A genuine subscription, It's the only thing that will give you back what your missing at the moment.

    An alternative would be iptv but you need decent bandwidth for it and most are paid services (payservers) which we are against on this forum.

    A motorised setup will get you a fair bit but in order to get shares, you probably need to give back in return, that said, not all your looking for will be in English.

  • VU+ Solo SE V2 Twin-S2 don't start

    If you cannot flash an image, you may have a power supply issue, can you get your hands on another power supply to double check that it's not your problem?

    This is the power brick spec:

    External power supply:

    • entrance:
    • 110-240V AC / 50-60Hz / 1,0 A
    • exit:
    • 12V = / 3,5 A

  • Cccam help

    If your using cccam, change your line from

    C: xx.xx.xxx.xxx 27080 D7xxxxxB mxxxxxxB 01 02 03 04 05 06 07 08 09 10 11 12 13 14

    To

    N: xx.xx.xxx.xxx 27080 D7xxxxxB mxxxxxxB 01 02 03 04 05 06 07 08 09 10 11 12 13 14


    Or if using mgcamd, try changing the beginning of your line to cws and enter it into your newcamd list (i think) eg:

    CWS: xx.xx.xxx.xxx 27080 D7xxxxxB mxxxxxxB 01 02 03 04 05 06 07 08 09 10 11 12 13 14

  • openvix cannot download plugins h.s

    Openvix doesn't officially support zgemma receivers.

    What you have is an image designed for another receiver, modified to run on a zgemma.

    Your best bet is to contact the site where you got the modified image from.

    I'm going to close this now,.

  • Slingplayer portable.

    This is an old post:

    Quote

    Calling all Slingboxers! SlingPlayer "Just Works" as a portable app :-)



    (Disclaimer: This may or may not be old news, but I did a forum search and didn't find any mention at all of this.)

    SlingPlayer works fine perfectly off a USB device, and thus in PortableApps. All you have to do is copy the "SlingPlayer" folder from (by default) "C:\Programs Files\Sling Media" to the device, or the "PortableApps" folder.

    taken from:

    Code
    http://portableapps.com/node/8097

  • oscam config for 2 card

    I presume you mean newcamd?

    I would use a separate port for each caid:

    Eg:

    Code
    [newcamd]
port                          = 20000@0963:000000;20001@0100:000068
key                           = 0102030405060708091011121314


    2 cards above , 0963 on port 20000 and 0100 on 20001

    Forget if you use a ; or , between port entries though (as highlighted above)


    I normally use cccam though, It only requires one port.




    What is the live log on your solo2 telling you when you try to access the problem card from your living room?

    If the above example doesn't sort it, post up your configs buddy (remove sensitive stuff), include whats in your living room receiver also, it'll make it easier for someone to see where the problem is.

  • add channel to bouquet

    Try updating your abm config first, it may have recent swaps incorporated.

    999c62d732215.jpg

    You could create a custom lcn for abm, if it doesn't work.

    There is a readme file located in:

    /usr/lib/enigma2/python/Plugins/SystemPlugins/AutoBouquetsMaker/custom (using openatv)

    I'm not too familiar with it, never messed with it, but seems straight forward.

    If you run into bother, abu baniaz is top man for it.

    Probably a bit futile in creating one at this point in time though , with all that's happening on 28.2.

    You may be better off to wait till it all settles down.