If your vu remote is sync'd to your tv (controlling on/off -vol +/- etc), you can easily change the receiver master volume using the webif.
Posts by codar
-
-
Try install the atv feeds:
http://linuxsat-support.com/attachment.php?attachmentid=20181&d=1386502265
Or give the linuxsat addons a go:
http://linuxsat-support.com/showthread.php?t=30475 -
Have you tried second cable in 1st tuner (to make sure everything on your satellite feed side is ok)?
Also, have you tried another image (dunno if vix officially support this receiver).
Openatv , italysat and opendroid are officially supportedQuote -
try putting it in through the "files" section on the webif and hit save, or just ftp modified configs to the receiver and delete the user backup file (user.bak). Make sure you keep a copy though, just incase things go wrong.
-
Oscam i presume?
Are you scrolling down the page to the bottom and hitting the "save" button?
Restarting oscam should then implement your modified configs. -
second cable goes in "Tuner B", "Lnb in"
Then, in service searching/ tuner configuration, you can set up your tuner for your dish. -
Wrong forum buddy.
Read the rules.
http://linuxsat-support.com/misc.php?do=vsarules
Thread closed -
All depends on your viewing tastes and budget.
-
Not too familiar with it to be honest.
Seems like a dm500 clone.
You could post up the configs for somebody to have a look (delete any sensitive stuff) , upgrade cccam to 2.3.0 or try changing to oscam.
You can find oscam (for dm500) here:Quote
Cccam here:
http://linuxsat-support.com/attachment.php?attachmentid=18489&d=1380352978Before upgrading, it is advisable to backup your configs.
-
1 You need something to share (card subscription/package)
2 Pc or receiver (some receivers can act as servers)
3 A card reader (omnikey 3121, smargo are the most popular) if your using a pc as a server
4 Reading up on how to do it can be found here:
http://linuxsat-support.com/forumdisplay.php?f=141
Any questions, feel free to ask.
What card are you thinking about as not all can be shared? -
Quote
He didn't ask for Vix support
Pluis asked for the best image
Quote
2) Whats the best image for Cloud iBox 2 Plus SE? OpenPLi, Balck-Hole, OpenATV,OpenVIX...or otherA good image for a receiver just doesn't constitute it running sweet, support is also a plus when choosing one. (especially when adding peripherals, plugins etc..)
Pheonix was pointing out that vix isn't supported for this receiver (although abruptly i admit) and has been modified by third parties to run on it.
As a member of the vix team, he is in a knowledgeable position to reflect this. -
Quote
See if you can spot my fake wetek under my TV haha
Does everything vibrate when its running??:laugh: -
Glad your sorted, i'll close this so.
-
Probably need more info/ image, configs etc for anyone to help really.
-
Have you got cccam to work using your external ip from within your network?
If not, your problem might be your router not supporting nat loopback.
Not all routers can support this and some which do, have the facility turned off.QuoteDisplay MoreNAT loopback
NAT loopback, also known as NAT hairpinning or NAT reflection,[6] is a feature in many consumer routers[7] which allows a user to connect to his/her own public IP address from inside the LAN. This is especially useful when, for example, a website is hosted at that IP address. The following describes an example network:
Public address: 203.0.113.1 (this is the address of the WAN interface on the router)
Internal address of router: 192.168.1.1
Address of the server: 192.168.1.2
Address of a computer: 192.168.1.100If a packet is sent to the public address (203.0.113.1) by a computer at 192.168.1.100, the packet would normally be routed to the default gateway (the router), unless an explicit route is set in the computer's routing tables. A router with the NAT loopback feature detects that 203.0.113.1 is the address of its WAN interface, and treats the packet as if coming from that interface. It decides based on DNAT (port forwarding) rules on the destination for the packet. For example, if the data were sent to port 80 and there is a DNAT rule for port 80 directed to 192.168.1.2, then the host at that address will receive the packet.
If no applicable DNAT rules are available, the router's firewall drops the packet. An ICMP Destination Unreachable reply may be sent. If any DNAT rules were present, address translation is still in effect; the router still rewrites the source IP address in the packet. The computer (192.168.1.100) sends the packet as coming from 192.168.1.100, but the server (192.168.1.2) receives it as coming from 203.0.113.1. When the server replies the process is identical as for an external sender. Thus, two-way communication is possible between hosts inside the LAN network via their public IP address.
NAT loopback is especially useful when the server hosts a domain name that resolves to a public address. When the router does not perform NAT loopback, any connection attempts to that IP address fail.
Wikipedia.
If you can see your ports are open (canyouseeme.org) then more than likely it should work using your dns/ip from outside your network but giving a temp share to a friend/ using a different network (connect solo2 to mobile hotspot on phone if your solo2 has a wifi adaptor) will be the acid test.
-
-
Quote
<2> If you are the supporter of a Pay Server DO NOT ask for support, your request will be ignored.
Please read the rules again:
http://linuxsat-support.com/showthread.php?t=15391
Also have a look here, it will explain the basics:
http://linuxsat-support.com/showthread.php?t=90
Thread closed. -
You'll have to sign up for a satellite package. P0rn cards seem to be a good starting point, or a sports package.
Have a read here, it will explain the basics:
http://linuxsat-support.com/showthread.php?t=90 -
There are a couple of teams supporting this receiver, ViX Team, Openmips, OpenATV to name a few.
Check out the "Nightly Builds" tab on the navbar (near the top of the page)to get the teams latest image. -
Quote
So the cccam.cfg file should only contain the lines I receive from my provider right
Are you paying your provider for your lines?
