hello everyone, it is normal for my zgemma h9 combo decoder to fail to work on the remote control, to make it work I have to restart the decoder from telnet:wtf1:
zgemma remote control
-
- Zgemma OpenATV
- Remote Control & Mapping Support
- beps
- Thread is marked as Resolved.
-
-
use the mobile phone trick
look at the end of your remote control infrared through your phone camera. See if the buttons are working
-
yes you know the trick works only on android phones heheh, the remote control and I have deleted the openatv6.3 from slot 1 installing the openatv 6.4 and I'm having problems I turn off the decoder, I turn it on then the remote control works I try to change channels and it doesn't work
-
the decoder does not load the drivers of the remote control in startup I am not very lucky :)
-
hi, if you are also far from your receiver and you have difficulty changing channels or anything else I would like to share what I found useful I will put screenshot under the wifi keyboard the usb is possible to insert on the front door it is possible to close and its range of use exceeds the 10 meters away
-
Ciao Amico è possibile che non funzioni il telecomando, se vuoi provare una soluzione stacca il dec e lo monti in un'altra TV
ci potrebbe essere una lantana possibilità che il dec va in conflitto con la tv.
-
hai , Pippomous
this keyboard has solved my distance problem now I can change channels much simpler I don't need to point the remote control to the box
while on my tv I have a source problem if I change the source on startup boot decoder on startup the remote control does not work but the keyboard always works and is very useful if you use plugs like kodi or youtube
-
ok beps,
it reduces your search on kodi
I read in another post with Gorski
that you edited the directors for various reasons,
of usb I have hdd and it is possible that the sofwere is corrupt you tried to reinstall everything
ho gave you this mistake from the beginning.
a hug friend
-
I wanted to share my solution at the low power distance of the original zgemma remote control
----------------------------------------------------------------------------------------------------------------------------------------------------
claims that it is possible that the firmware saves the data cache,.config etc. on usb instead of on rom I have not been able to set it even by making a new boot-image and sd save fash
-
Ciao hai trovato quello della tastiera come soluzione ora mi spiego perché il fumo ti usciva dalla testa
-
My Combo reacts well to RCU commands, no problem. Only if my foot or duvet are in the way, then yes...
-
-
I have similar issue with h9 twin, I can boot my box with the remote no problem, but when it's up and running, sometimes the remote just doesn't work and only hard restart fixes the issue, what I've noticed it only happens after first boot after few hours of deep standby
-
It happens to me too, often after the first start I find out that the remote control is not working, or rather it is the decoder that does not seem to react to the commands. I'm forced to restart and then everything works regularly
Zgemma H9 combo
-
Make sure you have not enabled HDMI-CEC
flash the box new and install wooshbuild new too
-
Make sure you have not enabled HDMI-CEC
flash the box new and install wooshbuild new too
Why wooshbuild its outdated and mean tied to openatv 6.4
-
i had hdmi cec off cause it doesnt work with my tv anyways, but lately i turned it on and the problem seems to be gone
Zgemma H9 Support Forum - Combo Tuner DVB-S2X DVB-C/T2 Linux Enigma2 Multi-stream QT Stalker WiFi Digital Receiver
Download Zgemma H9 Twin SE, Zgemma H9 Combo, Zgemma H9 Combo SE, Zgemma H9s and Zgemma H9s SE 4K UHD Series Images and Enigma2 Team Support from OpenATV, OpenBh, OpenDroid, OpenESi, OpenHDF, OpenPLi, OpenLD, OpenSPA, OpenViX, OpenVision, PKT Hyperion, PurE2, SatDreamGR, Sat-Lodge.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!