Thanks Yensen Command diseqc port ABCD.This is ok for 4 satellites.
If you put them with 8 satellites, I don't see the EFGH port....etc....
Wave Frontier T90 installation - setup guide - advice needed
- kaspas
- Thread is marked as Resolved.
-
-
No I have Astra (19.2E) in the center to have more satellites available to left and right side (on the lnb mounting bar.
Sorry maybe you are right. I do not remember (toroidal dish installed more than 10 years ago) but HotBird should be in the center
-
In fact the center satellite is important only in the sense of your choice of global reception satellites....
If we estimate that with your dish you can receive more or less 40 degrees of reception....if you want Hispasat at 30 degrees west, it will not be the same as if you want Turksat at 42 degrees east.....
Assuming that you start from Thor at 0.8 degrees west, you can go east to 19 degrees and the same amount to the west.....based on the total 40 degrees.....
-
Hopefully one of these guys that is using switches will answer as to how they have there sats and tuners configured
I use diseqc in a different way
-
Regarding the connection with a disecq century 8 inputs for example, that's what I use and I even added a little extra that I'm going to show you....
So I have 7 positions with my T55 dish, I of course do not receive all the frequencies of 28.5 for example or Thor, but I have 5 degrees west, 0.8 west partially, 9° east, 13° east, 19° east, 23 and 28.5 east....and on the last entry, I have a small motorized dish which works perfectly well, I know that for the pros, it will make them laugh, but as I I like tinkering, I tried and I put 2 images of the classic sats connections from 2 to 8 for the inputs, corresponding of course to the disecq inputs and input 1 for the motorized one....
Disecq mode 1 for the 7 fixed ones and their predestined numbers in disecq command and disecq mode 1.2 for the motorized and command 1 for the entry and it rolls.....
-
I know bubble is not ideal but I did all myself (not a pro... was hard anyway lol)
That is by far the most important part of the job !!
Slow down and get that absolutely perfect before doing anything. The way you are checking it in the 2nd picture is not correct.
Remove the dish and measure just the bracket that the dish mounts to. Again this 100 thousand percent MUST be perfectly aligned.
You will find the whole job much easier if working with a level bracket to begin with, i can not stress this enough.
-
somebody have some experience idea or some method to catch sat positions away from center position... ?
It's all about alignment. Pay attention to the final part of this manual.
Maybe left part is ok but the right side is too high or low, or viceversa?
-
I know bubble is not ideal but I did all myself (not a pro... was hard anyway lol)
Remove the dish and measure just the bracket that the dish mounts to. Again this 100 thousand percent MUST be perfectly aligned.
Yeah that was a thing I have in my mind and I need nearly a day to do this ...
-
That might be a reason I`m not getting a picture at all on corners ? I guess...
Yes i would say so. One degree out at the centre point would be a lot more at either end of the arc.
-
Hi everyone, I don't really understand why we went with a T90 title, so toroidal dishes with double reflectors, while in the photos we see a multi+head Bigsat type dish???????
-
Hi everyone, to find the various sats, you must already have your mast right on 2 planes....and then you put yourself on a powerful frequency on the screen and be sure to be received in your place of residence .....and you search by slowly moving your Lnb....and if nothing is in front and if your mast is very well adjusted, it must work....Don't hesitate to put good Lnb type Inverto Black Ultra for more difficult sats.....
-
Hello
Something strange is happening to me...!
I have a 7 lnb system, (13°,16°,19°) but so far I have only ever used 3!
Today being at home I tried to arrange the other satellites, adding 26°, 28°, 9°.
If I set the advanced configuration I have no signal in any satellite.! If instead I set it simple, I have the signal in all 3 satellites.
But even if I add a simple setting with 4 satellites I still have no signal...!
Master your satellite setup with expert installation support.
Get dish alignment help, LNB guidance, and configuration tips for single, multi, and motorized systems. Your technical forum for satellite installation. Get support for LNBs, DiSEqC switches, motorized systems, actuators, and dish alignment for any setup.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!
