dear all, I'm on a fresh install of OpenATV 7.5.1 and facing strange issue. My tuners are set properly and services are working fine.
when I try to record, I have an error on the picture attached, any ideas, please? thanks
recording not working
- jurajdrobec
- Thread is marked as Resolved.
-
Are you aware you can have multiboot ie 3 images, then you could flash vix, opbh, and opnatv, try them and pick the best. i would not use openatv but why did you do a fresh install? Try this but you should say skin and are you on fixed sat etc.
1. turn off, power off at rear, if you have 2 sat cables swop them over.
2. power back on, check if you have anything in timers and autotimers.
3. go to a channel press record, report back, you may have missed a step with the install, do a pic of tuners
-
I think nothing to do with openatv but FBC tuners are not set correctly.
-
I am recording 4 channels to test your issue. This is using ATV 7.51 01/07/2025 image on a duo 4k.
Please describe what receiver you have. How many tuners you have.For each tuner, describe the dish/LNBs attached to it. Then describe what you have configured those tuners as. And which channels and on what satellite those channels are on.Edit:
Sorry, phone does not show the section of forum. I did not see that this is the Uno 4KSE section.
-
tuner settings ? I have DUO 4K SE openvix and 5 tuners and can record minimum 4 at a time.Image chooses itselfs to create virtual tuners when recording even with normal LNB's
-
tuner settings ? I have DUO 4K SE openvix and 5 tuners and can record minimum 4 at a time.Image chooses itselfs to create virtual tuners when recording even with normal LNB's
perhaps but discussion is openatv.
-
should be the same
-
Very little details. However, VTI does the daisy chaining of tuners. PLI, VIX, ATV, OBH and others do not daisy chain. ( ATV is a recent change). On these images, the linkage is to the tuner(connection) with the signal wire. VTI is to the previous tuner letter.
If you want to resolve your issue, please respond back with:
Tuner A: Describe the dish/LNBs physically attached to it.
Tuner B: Describe the dish/LNBs physically attached to it.
Post screenshots of tuner configuration for all 8 tuners. That's 8 screenshots.
To grab screenshots, see this thread. Go to the web browser section.
https://www.linuxsat-support.com/thread/107704-how-to-take-a-screenshot-on-any-enigma2-receiver/?pageNo=1
Please state the names and on what satellite the channels you are trying to record are on.
-
thanks to all for suggestions, 7.3 solved my issue
-
thanks to all for suggestions, 7.3 solved my issue
That did not solve your issue your issue was with version 7.5.1.
-
7.3 is using the old tuner code. Anyway, glad you think you are sorted. You will encounter the same problem if you use newer ATV or other images.
I saw from your other post, you have configured your tuners as one having a motorised dish and another being fixed on 23.5. This means you have two physical dishes connected to the receiver.
If you have one motorised dish with a dual output LNB, that is the wrong configuration.
-
You will encounter the same problem if you use newer ATV or other images : why because many openvix users from that box and not one off them has problems with the newer images 6.7 on 4K boxes
VU+ UNO 4K SE PVR ready Linux Enigma2 Receiver UHD 2160p
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!
