OpenATV-8.0 beta image for all

There are 246 replies in this Thread which was already clicked 53,078 times. The last Post () by Captain.

    Quote from urie
    Quote from n@ki

    zgemma h9 twin se

    Onu göremedim, dostum.

    Hayır, ama en azından nereye bakmanız gerektiğini biliyorsunuz veya sadece "var mı?" diye sormak yerine doğrudan resim talep ediyorsunuz.


    Ayrıca OpenATV forumundaki kutu yapım isteği başlığında birinin Zgemma H9 Twin SE için görsel istediğini de fark ettim. :)

    thanks

    I’m posting this in the hope that someone can find a solution (I’d hoped that updating to version 8 would resolve the issue, but it didn’t). Since updating to version 7, my EDISION OS Mio 4K Plus has had two major issues which didn't occur when I was using version 6. The problem is twofold, but I think it stems from the same source (Python?). Firstly, the decoder does not come out of deep standby mode (it freezes halfway through booting up), and secondly, when it comes out of normal standby mode, it appears to work, but it does not receive any channels. In both cases, I have to disconnect the power by pulling the plug out of the socket for a few seconds to restart the decoder properly. Please help! Thank you.

    Quote from urie
    Quote from mp59

    I’m posting this in the hope that someone can find a solution (I’d hoped that updating to version 8 would resolve the issue, but it didn’t). Since updating to version 7, my EDISION OS Mio 4K Plus has had two major issues which didn't occur when I was using version 6. The problem is twofold, but I think it stems from the same source (Python?). Firstly, the decoder does not come out of deep standby mode (it freezes halfway through booting up), and secondly, when it comes out of normal standby mode, it appears to work, but it does not receive any channels. In both cases, I have to disconnect the power by pulling the plug out of the socket for a few seconds to restart the decoder properly. Please help! Thank you.

    And when you mention updates are these actually updates and not clean installations without restoring settings.

    because you cannot carry over settings backups from 6 to 7
    you should enable debug logs.

    Hi!
    I wrote ‘from version 6 to 7’ and ‘from version 7 to 8’ to make it clear that the decoder stopped working properly from version 7 onwards, but all my installations were clean installations. I’m no expert in firmware for Linux-based decoders or in log analysis, but I know full well that when changing versions or encountering bugs, it’s always best to start from scratch.

    Edited once, last by mp59 ().

    Quote from mp59

    I’m posting this in the hope that someone can find a solution (I’d hoped that updating to version 8 would resolve the issue, but it didn’t). Since updating to version 7, my EDISION OS Mio 4K Plus has had two major issues which didn't occur when I was using version 6. The problem is twofold, but I think it stems from the same source (Python?). Firstly, the decoder does not come out of deep standby mode (it freezes halfway through booting up), and secondly, when it comes out of normal standby mode, it appears to work, but it does not receive any channels. In both cases, I have to disconnect the power by pulling the plug out of the socket for a few seconds to restart the decoder properly. Please help! Thank you.

    And when you mention updates are these actually updates and not clean installations without restoring settings.

    because you cannot carry over settings backups from 6 to 7
    you should enable debug logs.

    I wrote ‘from version 6 to 7’ and ‘from version 7 to 8’ to make it clear that the decoder stopped working properly from version 7 onwards, but all my installations were clean installations. I’m no expert in firmware for Linux-based decoders or in log analysis, but I know full well that when changing versions or encountering bugs, it’s always best to start from scratch.

    Quote from urie
    Quote from mp59

    I’m posting this in the hope that someone can find a solution (I’d hoped that updating to version 8 would resolve the issue, but it didn’t). Since updating to version 7, my EDISION OS Mio 4K Plus has had two major issues which didn't occur when I was using version 6. The problem is twofold, but I think it stems from the same source (Python?). Firstly, the decoder does not come out of deep standby mode (it freezes halfway through booting up), and secondly, when it comes out of normal standby mode, it appears to work, but it does not receive any channels. In both cases, I have to disconnect the power by pulling the plug out of the socket for a few seconds to restart the decoder properly. Please help! Thank you.

    And when you mention updates are these actually updates and not clean installations without restoring settings.

    because you cannot carry over settings backups from 6 to 7
    you should enable debug logs.

    I enabled logs to check before to ask here, but I'm not able to debug by myself. Where can I post it?

    Quote from mp59
    Quote from urie
    Quote from mp59

    I’m posting this in the hope that someone can find a solution (I’d hoped that updating to version 8 would resolve the issue, but it didn’t). Since updating to version 7, my EDISION OS Mio 4K Plus has had two major issues which didn't occur when I was using version 6. The problem is twofold, but I think it stems from the same source (Python?). Firstly, the decoder does not come out of deep standby mode (it freezes halfway through booting up), and secondly, when it comes out of normal standby mode, it appears to work, but it does not receive any channels. In both cases, I have to disconnect the power by pulling the plug out of the socket for a few seconds to restart the decoder properly. Please help! Thank you.

    And when you mention updates are these actually updates and not clean installations without restoring settings.

    because you cannot carry over settings backups from 6 to 7
    you should enable debug logs.

    I enabled logs to check before to ask here, but I'm not able to debug by myself. Where can I post it?

    You post log here for the attention of captain or ideally on openatv forum look here information-about-the-8-0-0-alpha-test-image-en and on openatv

    OpenATV 8.0.0 PY3.14.x/OpenSSL 3.6.1

    if on openatv remember to fill in profile with box details.

    Starting from the 27.03.2026 build, it's not possible to run a script on a USB drive from within the file manager. Selecting "OK" just open the *.sh file but doesn't run it anymore.

    ZGemma H9S SE (currently in deep standby mode)

    Novaler 4K Pro Ultra HD - OpenATV 8.0 beta - Egami 11

    Edited 3 times, last by s2gus24 ().

    Thanks! I'll reproduce the issue on the decoder, save the debug file, and then ask for help on the forum. Unfortunately, I don't speak or understand German.

    there is translator on site

    Capture.PNG

    Hi, guys! In my opinion, OpenATV 8.0 being even in Alpha stage, is great.

    It provides all that is needed to watch satellites channels.

    Team. keep pace! You are actually the best. Don't pay attention at the "bugs" hunters.

    Ustym 4k Pro.

    Edited once, last by sergio60 ().

    I want to install OpenAtv 8.0 via flash online in the multiboot sector of DM 7080 HD. But in the corresponding slot, only the image name is OpenAtv 8.0 while in fact it results in OpenAtv 6.0 (the last image installed on 08.03.2026)?

OpenATV Team Images Support Forum ~ based on OE-Alliance

OpenATV Supported Models ~ Airdigital, Amiko, Anadol, Atemio, Atto, AX Technology, Axas, Beyonwiz, Dinobot, Dreambox, Edision, EVO, Ferguson, Formuler, Galaxy Innovations, Gigablue, Golden Interstar, HDBox, Hitube, James Donkey, IQON, Izibox, Jepssen, Maxdigital, Medialink, MaXytec, MediaArt, Megaset, Miraclebox, MK-Digital, Mut@nt, Novaler, Octagon, Odin, Optibox, Protek, PULSe, Qviart, Red-Eagle, Relook, Roxxs, SAB, Sezam, Sogno, Space, Spycat, Technomate, Telestar, Tiviar, T-Rex, Uclan, Venton Unibox, Vimastec, VisionNet, VU+, VUplus, World Vision, Vizyon, WWio, Xsarius, and Xtrend.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login