hi all
i have setup my cccam 2.1.4 with 3 test flines, i am using my dm800hd with boxkey I then setup my cccam 2.1.4 config.cfg. I sent 3 flines to m8's to try and i requested a share on this site.
Dismal Results: They cannot see my server so I looked at cccam info page and no clients are shown, there is servers thatfor which i have a cline showing and the cline is active on my dm.
When I ran port forward, it reports a green light on TCP and says that my port is open on another device (i assume that to be my dm), on UPC is says it can ping my router, but the port is not open or reachable,
Any ideas to resolve this please so that I can share?
:blabla:
16001 sees servers but not clients
-
- Various Support
- junger
- Thread is marked as Resolved.
-
-
-
Do you have a static or dynamic DNS address? If you're dynamic create an account with Dyndns and setup a host record. PLi? Images website
Then setup your router to automatically update dyndns (if it has that feature) or on your Dreambox Blue button -> Services/Daemons -> Inadyn (Dynamic DNS Client).
Now give your mate your DynDNS hostname.
-
Sorry, the host dyndns shows a green circle with a tick, underneath it says status good, i will download the cs studio. I am using atenda wirless router, could it be any settings in the router/
-
Check the server listen port in your cfg matches what you have forwarded in your router.
Use Open Port Check Tool to check its forwarded properly.
Also post an example of your cfg ( hiding pass & ports ). -
Success: I can see your service on 82.29.*****on port (16000)
Your ISP is not blocking port 16000 -
im using windows 7 64bit, cs studio maybe takes 10 refreshes before anything is displayed, on a xp netbook it displays straight away, if you hae a similar setup its maybe worth trying refreshing a few times
-
SERVER LISTEN PORT : 16000
SMARTCARD CLOCK FREQUENCY : /dev/sci0 3430000
BOXKEY : /dev/sci0 ** ** ** **
F: junger *****2 0 1 { 0:0:1 }
F: junger **** 2 0 1 { 0:0:1 }
F: junger****2 0 1 { 0:0:1 }
F: junger ***** 2 0 1 { 0:0:1 }Does this help?
-
master G, you were on the ball last night with my cccam 2.1.4. is there a tutorial for the cs studio, it looks awsome but complicated to setup
-
master G, you were on the ball last night with my cccam 2.1.4. is there a tutorial for the cs studio, it looks awsome but complicated to setup
Click the icon that looks like a tool in the top left corner,, just enter the ip address, port 16001, username and password for the dreambox and click add.
Close cs studio down and restart it, click on the ip address in the top right and click update.. -
Current time : 20:46:40
NodeID : **********
Uptime : 00d 02:06:26
Connected clients : 0
Total handled client ecm's : 0
Total handled client emm's : 0
Total handled LOCAL ecm's : 0 / 9 (0%)
Peak load (max queued requests per workerthread)Does that look right m8?
-
Connected clients : 0
Current Usage (ECM requests/h) : 0
Average Usage (ECM requests/h) : 0# AVU Username Country / IP Usage Connected Idle time Ecm / Ok OK% Emm / Ok Ver Last used share Ecm time
No clients shown
-
Sorted, the problem was 2 Cccams running at the same time, thanks to all
-
Though you might have mentioned the person who spent most of the night helping you ;)
-
Though you might have mentioned the person who spent most of the night helping you ;)
Rich, I meant no offence, you were awsome and I could not have done it without you, Its even better, your a Red
Many Thanks
Junger
CCcam Support Forum
Configs, discussion, downloads and guides for CCcam Softcam.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!