Hi
I have a new Ferguson 102e
I have updated the firmware
I have installed a patch
As read on forum
I am trying to install my Cline, I go to networking setup
App selection
I select Newcamd Client
Press red edit button
Now the problem starts
After pressing the edit button I see from top of page down
Server Number 1
Url blank.....do I put something in here?
Ping
Port...Port
User name
Start
Login
I put my port numbers in
I put user name in
I put password in
Press start
Press login...it then says connected
Obviously I cant connect to scrambled channels
So please what do I insert into Url so as to allow me to ping
Many thanks in advance
Sgw
Ferguson ariva 102e
- sgw869
- Closed
- Thread is marked as Resolved.
-
-
You need to put in your dyndns address or ip address into url.
eg: if your cline looks something like this:
c: somebody.dyndns.com port user pass
You need to put the "somebody.dyndns.com" part into your url.If your sharing internally (have your own server setup),
Your cline would look something like this
c: 192.168.1.102 port user pass
Then your internal ip goes into your url (the 192.168.1.102 part of the cline)Regards
-
Hello codar
Still in trouble, I put c: xxxxxxx.dyndns.tv into the url, tried to ping still failing
I put a space after c:
After it wouldn't ping I rebooted the box, went into newcamd client edit and the c: xxxxxx.dyndns.tv info was all over the place
Just c was in url
both port numbers were empty
username was dyn
password dns
Is it possible I have installed the wrong firmware and patch
Firmware was A102E _20140428_V1.26B3.abs
Patch 1679d1393529604Many thanks for your earlier reply
Best regards
Sgw -
leave out the "c:"
Just put in the "xxxxxx.dyndns.tv" into the urlRegards
-
Hello codar
I have tried every way possible inputting info into url still unable to ping/view scrambled channels
On the network setting page I am inputting username/password autoconnect to yes
Press login button successful
its then reads CA TYPE1 NDS...I don't know if this sheds any more light on the subject
Also do I need to manually input my Lan Mac address
Best regards
Sgw -
If it's getting "login successful" and "CA TYPE NDS" then it's connected to a server.
Is the line good, can u check it in another receiver?
I never needed to input any mac address.
Not sure about the patch u flashed either.
This one works for me using a 150 combo
http://linuxsat-support.com/showthread.php?t=57881 -
Hello codar
I have installed the patch you suggest, the patch is a php file is this correct
Can you please direct me from the start
I do a factory reset, all it clears are the channel lists
What do I then install is it just the php file or do I also install the firmware .abs packageI do know my connection is good and the line works in my other box, I am trying to set this one up as a spare
The working box is powered off and the Ethernet cable disconnected before I try the 102e box
Many thanks
Sgw -
Hi,
The patch is a .rar file. It needs to be extracted.
If u see it as php file extension then read :
http://linuxsat-support.com/showthread.php?t=44527This will show you how to install the patch.
http://linuxsat-support.com/showthread.php?t=13204Let me know how u get on.
-
Hello codar
Many thanks for your perseverance in this matter
Your last instruction ref me seeing php files might help me immensely
Over four hours today its been
1. factory reset
2. allcode+bootloader/upgrade file V1.26B3.abs
3. Trying to patch all I was getting was... no files
Now I see why, I will read your links and hopefully I will succeed
I was thinking of trying RS232 but I need to buy the cable
I will try now....if I fail I will take up your personal message offer
Once again many thanks
Sgw -
No problem, just hit thanks button under post.
If your buying an RS232 cable, make sure it's a null modem cable you purchase.
Handy to have if you get "ASH" error up on screen as it is the only way to bring the receiver back to life after a bad flash afaik. -
Hello codar
I changed compatability view and the patch downloaded as a rar ext file
Do I need to somehow extract a certain file from the rar file?
1. factory reset
2. allcode+bootloader/upgrade file V1.26B3.abs
After upgrade unit reboots, then all I see is the V1.26B3.abs...no additional files namely the rar patch
I have tried formatting three separate USB sticks always the same result no patch can be found
If there is anything else you can think of I would appreciate it
I am working away all day tomorrow
So early Friday I will be online
Once again many thanks
Sgw -
Hello codar
Latest, I opened the patch/rar file and extracted just the patch
Loaded onto 102e no problems
Using my other box to ping server all I need is to put IN xxxxx.dyndns.xx and it pings OK
I have tried that way with the 102e without success
Do you think I need to input everything in i.e. xxxx.dyndns.XX...then both ports
then username then password
autoconnect then login...and then try and ping
One last question
Because I am using newcamd would I put/try c:...or n:
also is there a space between : and the first server letter
Many thanks
Sgw -
Hi,
If you have a c-line, use cccam as emu. It will only ask for port once. Enter just the dyndns address in url. (leave out the "c: and space")
If you have an n-line, use newcamd client as emu. Enter just the dyndns address in url. (leave out the N: and space"). It asks for port twice, just input same port in both fields.
C-line looks like this "c: xxx.dyndns.xx port user pass"
N-line looks like this "N: xxx.dyndns.xx port user pass 0102030405060708091011121314"
Hope this helps.
Regards -
Hello codar
Setup everything, it says connected to NDS, still scrambled
I reboot NDS changes to unknown still scrambled
Could the stb be a dud?
Best regards
Sgw -
What package/channel are you checking it on?
-
28.2
I have replied to PM -
Issue resolved
I was able to try another line which worked perfectly
newcamd would not work at all on the 102eWithout the help from codar I would still be in a fix
many thanks codar
Sgw -
good to hear you got it sorted buddy !!
Fair play to codar :78:
closed -
master G
Moved the thread from forum Ferguson Ariva HD Support to forum Ferguson Ariva HD.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!