Posts by toysoft

You need via the menu, of the image, to validate the streamrelay use with every channel that works with icam, and it will show up (the ID of the channel) on the file /etc/enigma2/whitelist_streamrelay

Check also if in your /etc/enigma2/settings file you have the two lines below (these are activated via the OpenWebIf, but you can insert on the settings file yourself, while the box is in "init 4", then restarted with "init 3" after adding).

config.streaming.descramble_client=True

config.streaming.stream_ecm=True

You will also see on the menu, see below,

pasted-from-clipboard.png

then Press "menu" button on the channel, and then check if the streamrelay is active or not for that channel

pasted-from-clipboard.png

You can install in the usb, no problem

Then once installed on your usb you will have to go to the folder dreambox on usb and send command

./backup_dm7020hd.sh /media/usb

Above, you have the command to send with telnet/ssh/putty when you are in /media/usb/dreambox and it will generate you the .nfi backup file.

TS

You need to have an icam working with your operator (09F0), I think this one is not supported...

As you can see actually the ones known working (ID) are below,

098C:000000

098D:000000

09C4:000000

and this one is SKY IT, that uses a different key of the above ones,

09CD:000000

TS

On the box where you want to watch the channel (file whitelist_streamrelay in /etc/enigma2/), you need to set the channel to icam use, as well as set on the oscam.conf the line to validate it, and on Webif the proper configuration (on the client box).

On the intermediary server side, you just have nothing to do.

TS

oscam.conf on [global] section

disablecrccws_only_for        = 0500:030B00,0E00:000000,1884:000000,098C:000000,098D:000000,09C4:000000,09CD:000000

and as well add

[streamrelay]
stream_relay_enabled          = 1
stream_emm_enabled            = 1
stream_ecm_delay              = 0
stream_relay_ctab             = 0963,0961,0960,09C4,098D,09CD

I use this for my Reolink, an http via exteplayer3 but could be also via 4097 GStreamer

#SERVICE 5002:0:0:0:0:0:0:0:0:0:http%3a//IP-ADDRESS/flv?port=1935&app=bcs&stream=channel0_sub.bcs&user=admin&password=:NAME

#DESCRIPTION NAME

Quote from smoky

Thanks will try tomorrow.

Not sure If I did understand you correctly...

I ftp the dreambox folder in zip file in hdd and then the backup occurs after rebooting?

Yes, ftp the file tar.gz and unpack it on the /hdd, with the command "tar -xvf" + name of the tar.gz file,

Then you have the scripts on the dreambox folder (/media/hdd/dreambox), that you can run to generate the nfi file, the backup.

TS

Quote from smoky

Hi Toysoft ...Thanks

The backup tool is in the image as I do not have access to the box right now.

You have the file, here, unpack in the dreambox folder in /hdd

https://mega.nz/file/sFk0DQKZ#RwQMBaz2dRxhJx_jJJ8MY1a-l_1GdeR7a9wjaioIUtU

or

http://downloadcenter.japhar.net/images/enigma2/dreambox_backup.tar.gz

Then do the backup of the image, and I will flash my DM7020HD box, and you tell me which tests I have to do with it, to be exactly on the same situation as you and I will give you the feedback on how it behaves.

It's a command line tool, you launch with the .sh script, in the /hdd/dreambox folder and add the option /media/hdd so it stores the .nfi file on /media/hdd

TS

To set up a Sky UK LNB on a Dreambox running Enigma2, you need to access the receiver's satellite configuration menu, select the correct LNB type for your installation (likely Universal or SCR), set the correct frequencies for Astra 28.2°E, and then perform a satellite scan to find the Sky channels.

Here's a step-by-step guide:

1. Physical Connection:

• Connect the coaxial cable from your Sky LNB (Low Noise Block) to the "Sat In" port on the back of your Dreambox receiver.

2. Access Dreambox Menu:

• Press the Menu button on your Dreambox remote to open the main menu.
• Navigate to the Setup or System Settings section.
• Find the Service Searching or Satellite Configuration menu.

3. Configure LNB Settings:

• Select Satellite: Ensure the correct satellite for Sky UK, Astra 28.2°E (or equivalent), is selected or enabled.

  
  

• LNB Type:
  • If you have a standard Universal LNB or an older model, select "Universal".

    
    

  • If you have a Sky Q compatible LNB, you might need to configure it for Unicable (SCR) mode, depending on your specific LNB and receiver setup.

    
    

• Frequencies: Set the following frequencies for Astra 28.2°E:

  
  

  • Low Band (LOF1): 9.75 GHz
  • High Band (LOF2): 10.60 GHz
• Tone Burst: Set to "On" if you are using a Universal LNB, which helps select the correct band.

  
  

4. Perform Satellite Scan:

• In the same menu, select the option to "Scan" or "Auto Scan" the selected satellite.

  
  

• Choose to Scan for Free-to-Air channels or perform a Blind Scan if you don't have a channel list.

  
  

• The Dreambox will search for available channels, which may take several minutes.

  
  

5. Save Settings:

• Once the scan is complete, save your settings to add the found channels to your Dreambox's channel list.

Quote from Vincy792004

Esatto utilizzato solo 4097 , sulla infobar del canale c'è scritto MediaPlayer

Immagine ultima versione OpenBlakhole 5.5.1

dietro c'è GStreamer, il 4097,

TS

Quote from Vincy792004

Ciao a tutti

non ho utilizzato nessun opkg install

ho semplicemente sostituito 1 con ( 4097 )

Funziona tutto in maniera perfetta ( immagine stabile cambio canale Veloce )

Unica info: il Player utilizzato è MediaPlayer ( InfoBar )

Grazie a tutti per le info date.

Display More

Dunque stai usando GStreamer 4097, che gia va bene, e Exteplayer3 va ancora meglio (e fa i VoD), ma codice 500x.

TS

Quote from kodi1338

Recently released Openatv 7.6 on the box which hadn't been used in years just to provide reliable free to Air TV instead of streaming

However satellite Astra 28.2 is the location my dish is set for as per previous S@y setup when a customer however it is receiving no channels after manual scan and Auto scan

Any ideas what I'm missing or if I need to update as it's been years and just trying to get back into it now

There is a LOT of FTA channels on 28.2° (even without a Sky Subscription you have plenty of choice), are you sure you setup properly the LNB model/type ? As the one installed by SKY on the mini dish is different I believe, it's like Unicable I think, USALS ??? I let specialists explain, need to be setup particularly on that type, and not as a normal LNB as we all use normally.

TS

Quote from smoky

I do not see any deterioration of the capacitors shown in attachments.

To anyone in this forum scrolling this thread would like to know if you have a 7020HD version 1 clearing streamrelay channels. My box freezes. Either it is an issue with my box or with the model.

This freezing occurs both with newenigma2 image and openpli8 or 9star.

Streamrelay works perfect on 800se and 8000HD boxes.

Thanks for the support.

Display More

I have at least 5 of these boxes, contact me by email (t o y s o f t s @gmail.com) so I can check with the exact same installation as you have (you do a backup of it with my backup tool) and then I will tell you exactly the behavior with my DM7020HD boxes,

TS

P.S.: Here are the caps...

pasted-from-clipboard.jpg

Quote from Vincy792004

Se vorrei provare con openBlackHole

Devo installare qualche plugin per il cambio codec ?

Non si parla di Codec, ma di player, devi avere ffmpeg+exteplayer3 per questa 3za opzione, altrimenti di nativo c'è il player dvb enigma2/DMM e poi il gstreamer (4097).

Tutto questo deve essere nei feeds dell'imagine, e deve essere ancora supportata, dunque avere feeds attivi per installare se non c'è gia nell'imagine in nativo che installi.

TS

1) è il reader Dreambox/open standard (usato dal DVB)

4097) Gstreamer

500x) Exteplayer3,

dunque è a secondo del player, Exteplayer3 ha bisogno di meno potenza e funziona molto bene, dunque scegli quello che ti va meglio, certe imagini hanno i 3 players,

TS

Quote from ian1095

I think the answer is quite simple.

The DM 7020 CPU is just not powerful enough and your flogging a dead horse.

It works fine, a DM800HDse, also on IPTV Streams,

And as he told, on another one he has no problems... so this one has the problem... and on my past experience I had exactly the same situation, and it was the 3 big capacitors near to smartcard reader that were deteriorated, needing replacement... and it was going worst to worst, with time.

TS

Quote from smoky

I did untick the network. Suppose this does not make any difference except for increasing the time to upload the image.

However, using the option to recover bad sectors caused the box to freeze now even when streaming a local station in a bouquet. Streamrelay problem was not solved either.

So I did flash it again normally without the option to check for bad sectors.

Never had such a lengthy issue without finding the cause of the problem. I am suspecting that the problem is the memory.

Display More

Can you check the Capacitors on the motherboard ? I had one of my DM7020HD who had problems, more and more... and there were 3 big capacitors with a hill on top... near to the black smartcard readers.

TS

Quote from smoky

Thanks..

Is it necessary to untick network in dreamup when recovery of bad sectors is selected. It is taking long....

No, you don't need to untick network, its different thing.

On the menu of DreamUp/JapharFlasher, you have the option to activate, for checking the bad sectors, it will do the job while it flashes the box.

TS

Quote from smoky

I have made a new install of openpli9star a few moments ago. Could the issue of freezing be due to the error in picture while flashing the box?

The flash continued successfully as I did take the picture while flashing.

Curiosity: How come the new installed image kept my dreambox password in its memory?

It should not keep the password (or you kept the settings to be reloaded after flashing as it is possible on new boxes),

You could also try to flash with the Bad Sectory Recovery, it could perhaps change something (check good ones and bad ones marking them to avoid using defective Flash memory sectors).

TS

Quote from myscotom

For me there is a icam patch for oscam and you enable icam protocol.

I want to compiler oscam with icam patch and I want compiler oscam by myself

I have all oscam source, but I not found a icam patch.

Can you help me?

You have here, oscam-emu compilation from openpli github,

openpli-oe-core/meta-openpli/recipes-openpli/enigma2-softcams/enigma2-plugin-softcams-oscam-emu.bb at develop · OpenPLi/openpli-oe-core

OpenPLi Openembedded overlay for PVR settop boxes. Contribute to OpenPLi/openpli-oe-core development by creating an account on GitHub.

github.com

TS

Quote from brutus1979

Excuse my ignorance but if I download the entire channel list ( m3u ) , let's say...0.8W from webif (enigma2) will it work? As far as I know it's not a simple url...but I hope you'll help me when I get the device. Thanks again!

I have installed it, and remotely I change channel on my dreambox DM820HD (on the webif), the output of the device is directly the HDMI output, so you could output anything, like also playing a recorded movie on your Dreambox (but also could connect from your DVD Player, Blue Ray, or anything else)... there is no "limitation" as it decrypts the HDMI stream and transform it into TS/M3U8 Stream for any player to read/play. I love it (I bought 4 !)

Feel free to email me when you get it, and I will help you, it's very easy to manage (my email t o y s o f t s @ gmail.com)

TS