Posts by cazuela

kemestri ¿ has your UNO got a Vuplus DVB-S NIM (DVB-S2) tuner ?? something that comes to mind...

¿have you looked inside make sure all is well connected??

the more info you give about your setup and what you have tried so far,etc,,, makes it a little easier to help you .
read all the stickies HERE + HERE
apart from the obvious ( local sub card,image, open port in router,etc )

There are as many stories as there are posts to this weekend which could be told as Sandman has already written.
But there is one that you could not make up, ¿ was it a mere coincidence or fate??????
Each one with their own theory :

OK ,so I added the + just to make it easier to pick up ;)
Thanks lads for such an "eventful weekend" !!!!!!!!!!!!!
You make it even more than just another "sat-site" !!!!!
On a last note...... if it were ever to repeat itself , let´s make it somewhere more "caz_ needs-heat_compatible" ;)

could be either HYSTERICAL or HISTORICAL or a HYBRID version...lol

Quote from mckee25

Here's the ipk file for you for TS Panel,FTP it over to the temp folder and install it.

Having this on your image will makes things so much easier for adding and removing addons.

Also it give you access to our server,where you can install cams and plug-ins etc straight onto your box.

you obviously haven´t read the previous post that mckee so kindly searched( using the searchbar) for you which has the ipk which he prob found HERE the same way I did...

then go into menu- setup -CUSTOM -EXPERT --from there you have multi options.. or RECORD options,,i´m just comparing fro another image ( italysat).. but most are similar.. another option on this image is SUBTITLE SETTINGS.... one more option is AUTO LANGUAGE SELECTION.... have found options in all these sections..
happy hunting and lets know how you get on :)

havent had this problem as to date and dont have Bh image at the moment... but from memory YELLOW - subtitles- < arrows> then ok should clear it for you...¿ do they not appear when you are viewing ?? strange indeed!!
as far as epg...cooltvguide is one of the if not the best of epg guides.

there´s one good way to find out......... trying out then seeing is believing ;)
As musogeek wrote : he´s going from memory but it would only take you less then 5 to try it out and report back the results to help others ;)

as suggested above that or possibly too much caché still not cleared...
leave the box unplugged for a night then install the clean image I passed on in earlier posts and let it run for a while..
Not much else really comes to mind ,,but if you consider that within 3 days I have changed and uploaded 3 different backups without a hiccough then it gives you an idea just how resilient these boxes are...
I dont think it is bricked ..just in need of some TLC ( tender loving care ;)

what have you done ,changes ,new installation ,etc, to provoke the situation again??
I sometimes get this situation on my UNO if the image hasnt been properly fully 100% installed,,
by elimination of steps I put it down to a faulty usb penstick not the box....so try a different usb penstick and try installing again..

as long as they are within the same transponder frequency I dont see why not..
you´ll notice the channels you can view havent been greyed out using PIP for example.

so you want your server to not try reading from your card to open this channel ¿is this correct?but to be able to recieve it from another peer?
sid reject wont work with 2.1.3
but i think that adding SID ASSIGN would allow your card to be used to only the channels that you are subscribed to
you would need to make a list of these sids and add them to it..
this is the line I use for 7 channels of an MTV card opens:

Quote

SMARTCARD SID ASSIGN : /dev/sci0 7 { 6FF0, 6FF1, 6FFA, 6FEF, 6FF3, 6FEE, 6FFF }

you find the sids in a channel list .
i have it in the CCcam.cfg
Sorry i cant think of anything else

just found this might be of use : HERE

confused now ..please tell us exactly what you are using in setup ¿ ccam? ¿ oscam?? the more info the better we can understand to find a solution,,

you have to reboot box for changes..

try this in your config add SMARTCARD SID REJECT: /dev/sci0 { C5CB,C7A9 } or wherever it is reading the card from

@ andy ray you will notice that nicetobenice is not a VIP therfore he cannot view the thread you have posted.
@nicetobenice - this is a reduced version of the post :

Quote

I think if everyone did everything they could to stop their peers being affected from a card appearing to clear this channel when it is not, then things would be better - I think the following should be spread down to everyone's peers who have a sly local and don't subscribe to boxnation. There are other ways you can try to control it locally by controlling your clines to block out 0963 completely for peers who mess up your boxnation, or if you are using Oscam you can just block out the service using the oscam.services in their reader account (as mentioned further down with the services = !boxnation)

You need to work out which of your peers are giving you boxnation and which are not. If you are getting it on your hop 2 from a peer and it is intermittent, then your peer could contact his peer (who is giving him bad boxnation) to try to get him to sort it out. Have a chat with your peers, it is good to talk!!

A peer can block out sending you boxnation if they don't subscribe or can't get it to be read (which they should be able to in oscam) in their fline or Oscam user account. For them to stop peers getting Boxnation - In oscam they can use the oscam.services file. In here, they should add this entry (included boxnation and premier sports)

Code:

[boxnation]
caid = 0963
provid = 000000
srvid = C5CB,C7A9

and in your account in oscam.user they should add

Code:

services = !boxnation

They can also try to put the !boxnation flag in their reader entry in oscam.server for their card, and if they are sending the card to CCcam via newcamd then also can try putting it in the account entry that is being sent to their local CCcam server in oscam.user

People seem to have varying degrees of luck with the above method

It is also possible for your peer, who is using a CCcam server to block out these services in your fline direct
Code:

F: user pass 2 0 0 { 0:0:2 } { 0963:000000:C5CB, 0963:000000:C7A9 }

If their card is being read in CCcam direct, and they have 2.2.1 version or later, then the SID reject feature can be used to block out these services, and all services that the card can't read in fact.

Code:

SMARTCARD SID REJECT: /dev/sci0 { C5CB,C7A9 }

again above for boxnation and premier sports - and /dev/sci0 has to be adjusted to the address of the device that is reading the card.

Display More

any problems with installation in dm8000 , try this :

opkg install http://dreamboxupdate.com/opendreambox/1.6/dm8000/experimental/mipsel/python-html_2.6.7-ml8.2_mipsel.ipk

you cannot share what is not yours..simple as that.
if your paid period is up then you were either paying installments for the box or for a line from a p/s.
if you read from the first post ,,everything has been explained.. try it.

you can add as many clines as you like as long as they come from different IPs.
not the solo IP....this can only be one cline...
if they are clines from other peers you would simply add them to either box ,not the 2 boxes at the same time....
You need to clarify exactly what you have + what you are really trying to do.
your original Q was to use solo as server + use dm500 as client only..so... put all clines from peers + the cline from solo into dm500.(cline from solo will use the IP not the host name )
you really need to read the cardsharing BASICS in the cardsharing section HERE

yuo need to use the boxIP :

in SoLO server add : F: dm500 mine
the port is the one you have opened in router

then DM500 client : C: 192.168.1.xx port dm500 mine
thats it..as the dm500 is only client no need to open a port..
no need to put limits on end of lines as it is internally sharing not externally..
the IP in the cline is the internal IP of the solo