there is a python about SNR-AGC-BER
usr/lib/enigma2/python/Components/Converter/FrontendInfo.py
if you have an old box then you can replace it with that python
first copy the original one to Safe Place :)
there is a python about SNR-AGC-BER
usr/lib/enigma2/python/Components/Converter/FrontendInfo.py
if you have an old box then you can replace it with that python
first copy the original one to Safe Place :)
dear OJNIDOD
if it's Show snr when it's not Lock it's absolutly incorrect and it was an error
the correct SNR only show and measures when it's on LOCK situation
and if you want AGC- then it's not working on newer DM boxes yet-
if you have correct CAID for Channels on reader and Correct Code on cw or softcam
then you should see this log for your channel on webif
017/12/29 02:49:00 4F185EFA c (ecm) dvbapiau (2600@000000/0000/0067/0B:D957CEA795E0960B30D5AAB3E6F7F054): found (3 ms) by constant.cw
and this line for Softcam.key if you addressed the reader to /etc/tuxbox/config/Softcam.key
the picture you attached was ncam webif with logs
now what's the problem ?
if you want to see constant.cw on webif then you should add reader to ncam.server like these
[Reader]
Label = constant.cw
Protocol = constcw
Device = /etc/tuxbox/config/constant.cw
Caid = 2600,0B00,0500,0963,06AD
Ident = 2600: 000000; 0B00: 000000; 0500: 032830; 0963: 000000; 06AD: 000000
Group = 1
then you can see on webif and edit your address of cw
welcome
becasue of the ports assigned to oscam or ncam
try 8888 for oscam
ip.of.your.box:8888
and for ncam 8181 or 8080 or 81
to find the correct port you can try to opening oscam.conf or ncam.conf
you are welcome, :)
if you have a diseqc Switch for 3sats then you should do it in tuner configuration and change the A-B-C-D port
and for oscam i think it's not installed yet
put it on /tmp and telnet
opkg install /tmp/*.ipk
did you configure tuner configurations ok ??
if your configurations not correct then no signal and show you (tune failed)
and for oscam did you run it on cam manager ?
install unstable image (http://www.dreamboxupdate.com/…deb-dm520-20171217.tar.xz)
and then try with latest gp3wizard i attached to last post (ver2.4)
it should work nice with you
hi
you can reach to all of your questions with Search box (up right corner)
for example
idon't know where the problem is
but i cant understand cccam on 4K devices !!!
it's not supported on Arm devices from cccam developer yet !
its under network section
but it's not activated without configs so its not your problem
wait for others for support
:goodevening:
Hi, I get this problem in Oscam " oscam webif blocking localhost 127.0.0.1 " and if I go on a channel that maybe not working or whatever , Oscam freez and no possible to see working channels, Oscam goes working again after 1 minute or longer, what can I do , Please help new to Oscam , used to work with Cccam without this problem
did you running OPENVPN ?
if yes try another vpn provider
because some of them routing from local host to their server
i have successfully installed the GP3, and when i tried to run it it gives strange error "cannot satisfy dependencies for" and it didnt install the blue panel :( i tried googling it and tried to reinstall via Putty but same error, then just to check i flashed Gemini Image, which has Blue Panel built in, then installed the Ncam, inserted the line, Cam and line were successfully activated but didnt open any channel :(
i think your image was not updated to the latest version
always get the latest from dreamboxupdate.com and then try to installing gemini wizard
and here is the latest GP3 wizard
It's Emulator
Ithink You don't have GP3 (bluepanel) and you can't start emulators
the things you should have is Cam-panel or Setup-camd
first install the gemini plugin(G3wizard) and after that restart the box on the extensions tap on (gemini wizard)and wait until its ask for restart
now you have blue panel with blue button
now you can install gemini Cam Feed by onestep for emulators
both attached for you
gp-cam-feed-configs_2.1-r0.1_mipsel.deb
after that you can see the camd panel on bluepanel like these
You can download it from bluepanel or also install Ncam3.9 from Raed from here https://linuxsat-support.com/c…-images-520-820-7080-zip/
they both are very Same
Some advantages with 900 like (OE2.5) and Some advantages with uno4kse like Cpu
but
if i wanna buy i goes to
DM920 ;)8)
one Dual Fbc+Multistream tuner
one triple S2x-DVBC-DVBT
then i will have all the capabilities for Sat-cable-terrestrial-fbc-ms- s2x
Hi friend
You mean a small zero4k is more powerful than the costly one UNo4kSe???
its not about power
its only uncompatibilty with FBC tuner
because i think no driver for blind and fbc on enigma2 yet
Can I replace FBC tuner on Uno4kse with DVB S2X???
I don't know
better ask from world-of-satellite.co.uk
Sounds Good:thumbup:
the important point is unstable image on flash so another images isn't an important
you can use both unstable and stable on BAXII as well8)