Hi i need lateat Mohammed_OS OScam ubunto x64
Can please send it
in this thread we only discuss samur’s OSCam, for the other OSCams there are specific threads, use them
Posts by System
-
-
@linuxsat25 I wish you a speedy recovery
-
you had to set one of the 2 receivers by changing the remote control code
menu > setup > usage & GUIi > remote control code and assign a different code
So it is possible to use to gigablues in the same stack, as long as I change the remote control code
See page 98 paragraph 8 of the manual
Codehttps://store.gigablue.de/media/pdf/b3/ff/e1/Handbuch_eng_quad4k18122017.pdf -
you had to set one of the 2 receivers by changing the remote control code
menu > setup > usage & GUIi > remote control code and assign a different code
-
Have you already tried this procedure?
Turn off the switch behind it and then turn it back on by holding down the power button in front of the decoder. At this point you should be in recovery mode and you can choose whether to boot another image from multiboot or install a new image online
-
Display MoreDisplay More
can you create a e2 log with opkg and send me the log , here np with progress bar
if it helps you, zgemma H7C, update from gui, to complete the update you need to run opkg from telnet
can you create a e2 log with opkg and send me the log , here np with progress bar
if it helps you, zgemma H7C, update from gui, to complete the update you need to run opkg from telnet
in the log you say progressbar not stopped, i cant see it and enable opkg log too this info missing in the log
I'll try again…
as you can see from the image, by updating from gui it remains like this forever
only running opkg upgrade from telnet is successful.
when I update from the gui in the log it should be from line 858
you have not enable opkg log enable this thx
Can you please remind me where opkg log is enabled?
-
can you create a e2 log with opkg and send me the log , here np with progress bar
if it helps you, zgemma H7C, update from gui, to complete the update you need to run opkg from telnet
can you create a e2 log with opkg and send me the log , here np with progress bar
if it helps you, zgemma H7C, update from gui, to complete the update you need to run opkg from telnet
in the log you say progressbar not stopped, i cant see it and enable opkg log too this info missing in the log
I'll try again…
as you can see from the image, by updating from gui it remains like this forever
only running opkg upgrade from telnet is successful.
when I update from the gui in the log it should be from line 858
-
can you create a e2 log with opkg and send me the log , here np with progress bar
if it helps you, zgemma H7C, update from gui, to complete the update you need to run opkg from telnet
in the log you say progressbar not stopped, i cant see it and enable opkg log too this info missing in the log
thanks "Captain" I will try again with the next update, can you give me the exact command to generate the log? Maybe I need to raise the debug level?
I used the following command:
init 4 && enigma2 > /tmp/enigma2_log.txt 2>&1
-
can you create a e2 log with opkg and send me the log , here np with progress bar
if it helps you, zgemma H7C, update from gui, to complete the update you need to run opkg from telnet
-
you could try launching the oscam from telnet with this command
./"name oscam" -h and post the result?
where "oscam name" enter the name you give to the .bin file
-
when you put the new one in /usr/bin you have to rename it with the same name as the old one, otherwise it won't start
-
look at the video in the first post, minute 5:19, even if the audio is in Arabic it's not important, just watch
-
ok right
have you already tried from your mobile phone with the fing application if you can see if it has taken an IP address?
otherwise you just have to try from the serial port as "gobi2000" indicated
-
from what you say the interface works, have you tried to see in menu > settings > system > network > network card settings if it gives you an IP address?
-
check if the folder GradientFHD is present in the /usr/share/enigma2 folder
-
Hi Captain, I wanted to point out that by updating the SF4008 octagon box with the latest build of 11/17/2023, 08:14:19 the conax nCAMD cam for the canal+ channels does not work, the ciplushelper_5.4-r0 plugin is installed on the box, even by updating it to ciplushelper version 5.7 or 5.8 from the common interface menu, the CAM is not detected and does not clarify the channels relating to the subscription.
Coincidentally I am surprised to discover that by uninstalling the ciplushelper plugin the cam is detected and the channels relating to the subscription are decoded.
Is this behavior correct?
-
Very sad to hear.
R.I.P.
-
If you want to proceed with the automatic installation, the file must have the extension .ipk.
you can not add the .ipk extension to the tar file or rename it
but you can also install it manually with 2 modes:
- Once you have extracted the files on your MAC, send them to the decoder with an FTP client and place them in the respective folders and set the following rights on the files:
- 755 for the executable (oscam) and for the batch that starts the emu
- 644 for all other files.
- unpack the .tar file from the decoder after sending it with an FTP client.
- Once you have extracted the files on your MAC, send them to the decoder with an FTP client and place them in the respective folders and set the following rights on the files:
-
sorry for the intrusion
on all decoder?
if not, with which processor do you have the problem mips or arm?
did you install streamlink or serviceapp?
-
new addon tested ok
plugin-video-mediaset-1.3.2 italian
