Posts by tpmm

  • epg help and channel lists

    I want to install crossepg on vu duo2 but am not sure whether to install from:-
    a. linuxsat panel where there are three versions of CrossEPG - 0.6.2, 0.7.04 & 0.8.1
    b. openvix 4.1.011 main menu, plugins, Crossepg Downloader

  • Oscam config question re how can I share local CD NO card on 2 receivers at home

    I have to admit to being a confused here. I have a local Canal Di*it*l Norsk Card. At my house I have two dish setups, one is on 1.2.m [ground floor] and a 1m dish[ 1'st floor]. I have vu solo2 running openvix on the 1.2m system and vu duo2 on openvix on the 1m system. I would like to configure oscam to be able to read the card in the vu solo2 [1.2m dish] but share it to the vu duo2 [1m dish]. It would only be a local setup, the reason is that so often the weather prevents me from getting a signal off the 1m dish.
    Can I ask if anyone can help with the necessary config files. I hope this ok to ask, I have done quite a bit of reading but as I say I haven't got it sorted in my head yet. Thanks for any help.


    Edit ... I should explain that the card is currently in a non Linux box on the 1m system on the 1st floor ... as it reads/updates fine there.

  • Oscam-emu 11034

    Quote from joeuser

    Powervu channels do not just "open" the same as other channels with oscam. You need to look at the instructions closely and use the "stream relay" to view the powervu channels. Probably best to first test with an external viewer (like VLC) on a PC to verify it is working before you try to create the IPTV favorites for enigma2...


    Thanks for the reply. Below is a summary of actions I had taken before I posted the oscam.log above. I 'think' the actions are as detailed in the instructions. I haven't managed to get any powerVU to clear yet but I hope if anyone who has the time to read what I have done, then maybe they could show me where I am going wrong. I include the config files.


    Thanks again.


    1. Running openvix 3.2 build 009 on vudu02


    2. Install oscam oscam-1.20-SU-236-EMU-312-721-SB-11034-mipsoe20-komplett-minimal-libcrypto_static [1,594KB] from post 1 of this thread.


    3. SoftCam.Key - valid keys [I believe] in /etc/tuxbox/config/


    4. OpenWebif


    Download and Save the .m3u file for the current powerVU channel. Edit the hostname to 127.0.0.1 and the port to the stream relay port 17999


    5. Try in VLC i.e open the edited .m3u file -
    Your input can't be opened:
    VLC is unable to open the MRL 'http://127:0:0:1:17999/1:0:11:1:9:5A0000:0:0:0:'. Check the log for details.


    6. DreamBoxEdit


    In Bouquet details - IPTV and other streaming services, Add.
    In the resulting IPTV streaming details:-
    Stream Type = DVB/TS
    Service Data/Name = Name of channel
    Service Data/URL = The edited stream link from point 5 [above] as URL
    DVB/TS Data/Service Id = As for the original channel and in decimal [not hex]
    DVB/TS Data/Service Type = 1
    DVB/TS Transponder Id = 11
    DVB/TS Network Id = 22
    DVV/TS Namespace =33
    Save


    7. OpenVix doesnt seem to support "Include ECM in http streams", I couldn't find it in OpenWebif/Settings/Customise.
    Tried adjusting the "ECM fix delay" setting in oscam webif (Config -> Stream Relay).



    8. Try IPTV favourites on vudu02 - select the channel, Stream 127.0.0.1%3a17999 [start of transponder reference] is displayed in bottom left hand corner of favorites screen, OK, black screen.


    9. Try to watch it from channel list, channel infobar shows Protocol: emu Hops:0 ecm: 0.001


    10.Oscam config files as below




    Code
    oscam.user




[account]
description                   = dvbapi
user                          = linuxsatsupport
group                         = 1,2,3,4,5
keepalive                     = 1

  • Oscam-emu 11034

    Was wondering if I posed my oscam.log in this format, if it might help identify the cause of the problem I am having. Thankyou.


  • Oscam-emu 11034

    Hi again - I believe I now have a SoftCam.Key file configured for PowerVU, the contents at the moment are for just one set of channels. Everything appears ok [i.e. no obvious errors in oscam.log] but none of the target channels are clearing. I believe I have the rights keys. I attach the oscam.log with certain fields obliterated. Would be grateful for any advice. Thanks again.

  • Oscam-emu 11034

    Thanks so much for that, I had tried to run it from telnet but got nothing back, but that was before I had restarted enigma2. Done as you say, and oscam now running. Thanks very much master G.


    - - - Updated - - -


    As a follow up to the above, I found that both
    oscam-1.20-SU-236-EMU-312-721-SB-11034-mipsoe20-komplett-minimal-libcrypto_static [1,594KB] &
    oscam-1.20-SU-236-EMU-312-721-SB-11034-mipsoe20-komplett-minimal-libcrypto_static-compressed [615KB] worked.


    - - - Updated - - -


    Would it be ok if I posted the start of the oscam.log to get some help re a specific highlighted error. I believe I have obliterated fields as required.

  • Oscam-emu 11034

    Quote from master G

    Did you change permissions on the oscam file to 755 then restart enigma2 ?


    I had changed the permissions to 755 on the oscam file but I hadn't restarted enigma2. I have now and have the same result as described previously.

  • Oscam-emu 11034

    Hi - I am running openvix 3.2 build 009 on vudu02. I have installed oscam emu 11034 from the attachment in the first post of this thread - specifically from build_dir_mipsoe20, oscam-1.20-SU-236-EMU-312-721-SB-11034-mipsoe20-komplett-minimal.tar , it is oscam [1,369KB from 04/10/2015]. oscam is available in the softcam manager menu and appears to start but doesn't run. I have checked this in telnet/ps, so there isn't a log and I can't connect to oscam-emu webif on port 8888. I have the oscam conf files set up as per this thread.
    I am wondering if I have done something wrong or perhaps this version of oscam is incorrect for openvix 3.2. Any advice would be much appreciated. Thanks

  • TS panel bad magic number

    Sure I was using TSPanel for cam installs, but I can do without it. I am just interested to know if there is a way to fix this issue, just keen to learn, find out new things, as always. This issue is one of several I have hit so far after installing openvix 3.2.

  • TS panel bad magic number

    Hi - have just updated my vuduo2 from Vix Hades 018 to Openvix 3.2 build 009. TSPanel 7.5 appears to install ok but when I select menu/plugins I get the following warning - this build has python 2.7.9. Any advice would be appreciated, thanks.


    0f906e.gif