Posts by Mee®kat

Quote from stevejo

http://linuxsat-support.com/showthread.php?t=4 this will explain that but you can still only log in once

Dont think so...i think 2 users can login to cccam with the same account at the same time/we are not sure what flavour of cccam is used with these boxes however as i think thats whats gone pete tong here///possibly stopping reshare might eradicate this problem? i dunno but 2 0 0 {0:0:2} is not a good idea on any cccam server..i remember that part as this allows reshare....2 is 1 reshare/3 is 2 reshare and so on...the boxes might be conflicting this causing issues?

MK

I,m not a cccam guru as i have been out of the loop with this cam for a few years now but looking at your post its obviously something to do with these new boxes...which version of cccam do they use?

F: test test 2 0 0 { 0:0:2 }

Also change your user flines to this F: test test 1 0 0 { 0:0:1 }

Only use 2 0 0 etc if you want your peers to have reshare !

MK

Bringing back some memories here macsporran as i used to own a sat company on the costa for a couple of years in early 2000...wish i was still there and i would be if it was,nt for the lack of work :(

Fitted plenty of 1.3 dishes too with cable runs upto 100 meters no problem/the cable i used for standard installations was from ntl cable engineers in the uk but when i ran out and had to buy some from traders namely (paco) in malaga it was always quality cable that had a foam filled dielectric..this was the only cable available to us at that time so the cable should be fine unless its suffered water ingress from a poor installation..i would'nt bother installing an inline amp either unless your bro in law thinks his box might have a weak tuner.

Official ***boxes are best to tell if you have signal problems but get your bro in law to see if the BER bar is showing anything high and if it is it will be as said above regarding dish alignment/like all countries that are fighting for a signal due to the footprint..lnb scew is very important and i mean by the millimeter.

Good luck amigo

mk

Quote from v1russ

Almost 350 Lol, :(

764ca4b5f0f5b3f9c4960ed.jpg

Highly doubt anywhere near 350 on an oscam server although i assume you want a ban for some reason?

Quote from v1russ

no, this is not a wrong forum, its a oscam Discussion... i have about 350 Clients connected to my OScam Server, but i want to save some info ,for identifying some users :) but thanks for your HELP :)

Cool...signed your own suicide note there dude...350 clients...yeeeehhhhaaaaaaaaaa

Goodnight Vienna !

Quote from v1russ

i want to collect informations about clients like this :

Name Surname username password expiry date phone location

1. John michael John_M 4392fvm 24.04.2014 355-444-6666 TX
2. ---- ---- ---- ---- ----- ---- --
3.---- ---- ---- ---- ----- ---- --
4. ---- ---- ---- ---- ----- ---- --

I dont know any excel form, or website template, is there any awailable Form ? Thank you

Display More

Why on earth would you need to extract such sensitive information? as nirmies says it looks like you defo are searching on the wrong forum.

BYEEEE

You might want to compare notes here mate http://linuxsat-support.com/showthread.php?t=45308&p=164660&viewfull=1#post164660

Similar issue although the viasat caid differs.

MK

Quote from v1russ

Hello all :) , maybe its wrong section, but sorry for that,
i am searching for a user registration form, i want to register all my clients that i have in oscam,
is there any method on how to do it , any web template. i want all just like oscan, create new user , expiry date :) ?

Your post is alarming to say the least mate but i,m not sure if i understand what you are asking to be fair....

What exactly do you mean by registration/register of users?

MK

Very strange indeed..has both of your friends bought these boxes from the same supplier? Also might be worth finding out if these units are clones.

If any of your other friends have the same box then you could maybe try and borrow the psu from it to eliminate a psu fault.

If it is a psu fault you might be best replacing the psu rather than trying to sort it.

MK

This will just be a basic mgcamd cfg problem...post it here so we can see what the problem is.

MK

Open pli images are best for streaming on dreamboxes.

Quote from dirtydonki

My VU+ DUO2 was made in China

Official Vu+ products are manufactured in Korea for the Belgian company as far as i know...however cheap clones of earlier Vu+ models and other e2 boxes are manufactured in China !

I think the Chinese will probably be the first to clone a human :)

MK

Another leech short of manners !

so ?

I think we might need to see an actual oscam log because that particular caid/provider you are using has recently developed some issues.

0B00 that is.

MK

Quote from sync

My point was that not every person you share with will be a good peer, even someone you might know for a long time through forums etc
Sometimes you need proof to confront them but I've lost faith in the basic share for share principle of Cardsharing, the way it was meant to be......these days it's all about how many share someone has or how big a cache or how much ram in their vps, these idiots make me want to vomit.

Unfortunately this has become a task that is included in monitoring and running a server...no **** sherlock is the phrase here really... we just have to get on with it or stop doing it.

Quote from sync

I was Cardsharing my legit nagra 1 card years ago when others spent every minute online looking for new keys after a key roll.

Now rant over for today :-)

Again not sure what this has to do with the price of butter but i also shared a nagra1 card years ago as a test due to the expected and inevitable encryption changes but i worked closely with a spanish friend and we developed a personal blocker for our mosc cards:) no running about for me looking for n1 keys back then that was for sure.

Quote from sync

Some of the numptys around these days make me feel sick !

Totally agree with you there tho sync as i cant figure this out myself how some peeps can even figure out how to switch a box on never mind tamper with sophisticated equipment...when i began this hobby which seems like a lifetime ago there was limited information to work on so we had to use our nogins and do some research....nightmare now is even with the vast information readily available peeps are still messing up with end result of toys out the pram...seems to me they expect to just plug a card into a box and start illegally sending expensive packages out all over the shop..looks like its just something we are going to have to accept on top of everything else:( not helping this hobby tho!

MK

Quote from snaper

Just wondering if anyone had any e2 cable bouquets they could post for Belfast thank you.

Probs best making your own list for that area mate as thats what i did for mine.

Quote from sync

I had a so called friend try to re-share my cards with multics a while back, how did I know ? well he stupidly left some ports open lol
So I confronted him on sk ype and he denied it so I sent him a screenshot of his multics, people who do that really piss me off.
Only share with trusted friends, keep yourself and your cards safe.

I am talking about anniman sharing the card via cccam not multics sync.

Not entirely sure what relevance your experience with someone ripping you off with multics has to do with this really.

Ports open is something we need to do with servers dont we sync so be more specific please.

MK

Quote from rgaraeh

Thank you for your response. So resharing setting is ok?
I can not use MgCamd, becouse i need multiprotocol client, this is the reason why i have OSCAM

this is newcs.xml

XML

<?xml version="1.0"?>
<!--




For setup-issues, look in readme.txt!
If there are other troubles, try different forums or irc channels around :o)




The configfile are NOT case-sensitive, and shouldnt care about dos/unix cr/lf.




** This is the example file for Dreambox/TD etc. that use SCI interfaces.




-->




<newCSconfig>
	<readers name="Card Readers">
		<device>
			<name>lower</name>
			<type>sci</type>
			<mhz>600</mhz>
			<node>/dev/sci0</node>
			<parity>odd</parity>
			<reset>normal</reset>
			<export>Yes</export>
			<enabled>Yes</enabled>
			<blocksa>No</blocksa>
			<blockua>No</blockua>
			<blockga>No</blockga>
			<!-- <boxkey>0000000000</boxkey>  -->
			<!-- <rsa>0000000000</rsa> -->
			<i*****-camkey>0000000000000000</i*****-camkey>
			<i*****-camkey-data>0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000</i*****-camkey-data>
			<crypto-special>No</crypto-special>
			<ipk>0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000</ipk>
			<ucpk>0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000</ucpk>
			<PTShandshake>No</PTShandshake>
			<carddetect>yes</carddetect>
			<newcamd_port>823</newcamd_port>
			<autosid>Yes</autosid>
			<Seca-PPV>no</Seca-PPV>
			<pincode>0000</pincode> 
			<priority>round</priority>
		</device>
		<device>
			<name>upper</name>
			<type>sci</type>
			<mhz>600</mhz>
			<node>/dev/sci1</node>
			<parity>odd</parity>
			<reset>normal</reset>
			<export>Yes</export>
			<enabled>No</enabled>
			<blocksa>No</blocksa>
			<blockua>No</blockua>
			<blockga>No</blockga>
			<!-- <boxkey>0000000000</boxkey>  -->
			<!-- <rsa>0000000000</rsa> -->
			<i*****-camkey>0000000000000000</i*****-camkey>
			<i*****-camkey-data>0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000</i*****-camkey-data>
			<crypto-special>No</crypto-special>
			<ipk>0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000</ipk>
			<ucpk>0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000</ucpk>
			<PTShandshake>No</PTShandshake>
			<carddetect>yes</carddetect>
			<newcamd_port>824</newcamd_port>
			<autosid>Yes</autosid>
			<Seca-PPV>no</Seca-PPV>
			<pincode>0000</pincode> 
			<priority>round</priority>
		</device>
		<device>		
			<name>smargo</name>
			<type>phoenix</type>
			<mhz>600</mhz>
			<parity>none</parity>
			<node>/dev/usb/ttyUSB0</node>
			<export>Yes</export>
			<enabled>No</enabled>
			<blocksa>No</blocksa>
			<blockua>No</blockua>
			<blockga>Yes</blockga>
			<blockc0>No</blockc0>			
			<boxkey>00000000</boxkey>
			<crypto-special>No</crypto-special>
			<PTShandshake>No</PTShandshake>
			<carddetect>yes</carddetect>
			<newcamd_port>34002</newcamd_port>
			<autosid>Yes</autosid>
			<Seca-PPV>no</Seca-PPV>
			<pincode>0000</pincode> 
			<priority>round</priority>
			<sid>
				<allow>
				</allow>
				<deny>
					<id></id>
				</deny>
			</sid>
		</device>
	</readers>
	<radegastserver>
			<enabled>No</enabled>
			<port>16000</port>
			<allow>
				<hostname>localhost</hostname>
			</allow>
	</radegastserver>
	<cache>
			<emm>20</emm>
			<ecm>-1</ecm>
	</cache>
	<httpd>
		<server> <!-- Port to accept connections on -->
			<port>8080</port>
			<enabled>yes</enabled>
		</server>
		<user>
			<!-- valid value for userfile are:
			     Any username you'd like - Used for browser to logon (its case sensitive).	-->
			<name>newcs</name>

			<!-- valid value for password are:
			     Any password you'd like - Used for browser to logon (its case sensitive).	-->
			<password>newcs</password>

			<!-- valid value for accesslevel are:
			     admin, stats - Define what rights the user has in the web-console	-->
			<accesslevel>admin</accesslevel>
		</user>
	</httpd>	
	<debug>
			<password>NewCSpwd</password>	
			<level>normal</level>
			<type>init</type>
			<output>console,tcp</output>
			<console_options>normal,init</console_options>
			<tcp_port>1001</tcp_port>
			<tcp_options>normal,init</tcp_options>
	</debug>
	<newcamdserver>
			<enabled>Yes</enabled>
			<name>newcs</name>
			<deskey>31 AA AA 12 09 F4 27 19 A2 18 1E 15 A1 21</deskey>
			<user>
				<name>dummy</name>
				<password>dummy</password>
				<hostname>localhost</hostname>
				<port>12000</port>
				<au>on</au>
				<sidoverride>off</sidoverride>
				<spider>No</spider>
				<rate>2</rate>
			</user>
			<user>
				<name>Joki</name>
				<password>Joki</password>
				<au>on</au>
				<sidoverride>off</sidoverride>
				<spider>No</spider>
				<rate>0</rate>
			</user>
			<user>
				<name>peter</name>
				<password>dum123</password>
				<au>on</au>
				<sidoverride>off</sidoverride>
				<spider>No</spider>
				<rate>0</rate>
			</user>
			<user>
				<name>dm800ts</name>
				<password>dm800ts</password>
				<au>on</au>
				<sidoverride>off</sidoverride>
				<spider>No</spider>
				<rate>0</rate>
			</user>
			<user>
				<name>dm800ov</name>
				<password>dm800ov</password>
				<au>on</au>
				<sidoverride>off</sidoverride>
				<spider>No</spider>
				<rate>0</rate>
			</user>
			<user>
				<name>dm800mb</name>
				<password>dm800mb</password>
				<au>on</au>
				<sidoverride>off</sidoverride>
				<spider>No</spider>
				<rate>0</rate>
			</user>
			<user>
				<name>mpcs</name>
				<password>dummy</password>
				<au>No</au>
				<spider>No</spider>
				<sidoverride>No</sidoverride>
				<readers>
				  <allow>lower</allow>
				  <allow>smargo</allow>				  
				</readers>
				<rate>0</rate>
			</user>
	</newcamdserver>
</newCSconfig>

Display More

Lost and confused.com//// let me get this right.....you setup a server for a mate with newcs but you wish to reshare his cards via oscam at your end...tell us why?

Mgcamd will read a line to check the server actually works! CCcam will do the same.

Quote from rgaraeh

Yes, I have permission, I helped him with NewCS, i do not know why he chose this server. May i post newcs.xml?

Looks like both of you dont have a scoobie then...yes you can post your newcs config but i would delete all ports if i was you/boxid id also delete that.

Mgcamd lines is newcamd which can be tested in bog standard/cccam or mgcamd...have you 2 even got this far?

Quote from sync

did your friend give you permission to re-share his cards ?

I agree as it looks like some sort of tomfoolery going on here?