Amiko Alien 2 Won`t Boot

gcstano · Nov 24th 2012

Hi to all, have the same problem with stucked alien2 on boot. I have tryed send the commands via putty but with no success.
here is all what i can see on putty:

Code

stm-ohci stm-ohci.0: stm-ohci
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00
usb usb2: configuration #1 chosen from 1 choice
[usb_probe_interface]drive name=hub
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
stm_usb_probe: usb_phy_clk clock not found for stm-usb.1
stm-ehci stm-ehci.1: st-ehci
stm-ehci stm-ehci.1: new USB bus registered, assigned bus number 3
stm-ehci stm-ehci.1: irq 143, io mem 0xfeaffe00
stm-ehci stm-ehci.1: USB 0.0 started, EHCI 1.00
usb usb3: configuration #1 chosen from 1 choice
[usb_probe_interface]drive name=hub
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
stm-ohci stm-ohci.1: stm-ohci
stm-ohci stm-ohci.1: new USB bus registered, assigned bus number 4
stm-ohci stm-ohci.1: irq 142, io mem 0xfeaffc00
usb usb4: configuration #1 chosen from 1 choice
[usb_probe_interface]drive name=hub
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
sh_tmu: TMU0 kept as earlytimer
sh_tmu: TMU1 kept as earlytimer
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
STMicroelectronics - Coprocessors st231 Init
st-coprocessor-0: No RAM reserved
st231.0 Coprocessor -------------------------------------------
    not configured!
---------------------------------------------------------------
st-coprocessor-1: No RAM reserved
st231.1 Coprocessor -------------------------------------------
    not configured!
---------------------------------------------------------------
stm-rng hardware driver 1.0 configured
heartbeat: version 0.1.1 loaded
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
NAND device: Manufacturer ID: 0x98, Chip ID: 0xdc (Toshiba NAND 512MiB 3,3V 8-bit)
stm-nand-flex: Using boot partition name [uboot] (from kernel config)
Creating 7 MTD partitions on "stm-nand-flex.0":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000b00000 : "Spark kernel"
0x000000b00000-0x000001200000 : "Reserve0"
0x000001200000-0x000001400000 : "Reserve1"
0x000001400000-0x000018000000 : "Spark Userfs"
0x000018000000-0x000018800000 : "E2 kernel"
0x000018800000-0x00001ff00000 : "E2 Userfs"
stm-nand-flex: Found BOOT parition[uboot], updating ECC paramters
boot-ECC 0x00000000->0x00100000
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
IP-Config: Device `e*th0' not found.
RAMDISK: gzip image found at block 0
VFS: Mounted root (ext2 filesystem) readonly on device 1:0.
starting pid 520, tty '': '/etc/init.d/rcS'
Welcome to STLinux!
waitting for peripheral device mount...ls: /tmp/: No such file or directory
cannot find /etc/network/interface
yaffs: dev is 32505860 name is "mtdblock4"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.4, "mtdblock4"
yaffs_read_super: isCheckpointed 0
mount ok
usr scripts
rm: can't remove '/dev/mtd0': Read-only file system
ln: /dev/mtd0: File exists
rm: can't remove '/tmp': Read-only file system
mkdir: can't create directory '/tmp': File exists
ln: /usr/lib/libcap.so.2: Read-only file system
ln: /usr/lib/libcap.so.2.16: Read-only file system
ln: /usr/lib/libcfont.so.0.0.0: Read-only file system
ln: /usr/lib/libconsole.so.0.0.0: Read-only file system
ln: /usr/lib/libcrossepg.so: Read-only file system
ln: /usr/lib/libcrypto.so: Read-only file system
ln: /usr/lib/libcrypto.so.0.9.8: Read-only file system
ln: /usr/lib/libcrypto.so.1.0.0: Read-only file system
ln: /usr/lib/libctutils.so.0.0.0: Read-only file system
ln: /usr/lib/libfreetype.so.6.3.18: Read-only file system
ln: /usr/lib/libglib-2.0.so.0: Read-only file system
ln: /usr/lib/libiw.so: Read-only file system
ln: /usr/lib/libiw.so.29: Read-only file system
ln: /usr/lib/libloudmouth-1.so.0: Read-only file system
ln: /usr/lib/libpcap.so.0.9.8: Read-only file system
ln: /usr/lib/libpopt.so.0: Read-only file system
ln: /usr/lib/libpopt.so.0.0.0: Read-only file system
ln: /usr/lib/libreadline.so.5: Read-only file system
ln: /usr/lib/libssl.so: Read-only file system
ln: /usr/lib/libssl.so.0.9.8: Read-only file system
ln: /usr/lib/libssl.so.1.0.0: Read-only file system
ln: /usr/lib/libstdc++.so.6: Read-only file system
ln: /usr/lib/libstdc++.so.6.0.14: Read-only file system
ln: /usr/lib/libusb-0.1.so.4: Read-only file system
ln: /usr/lib/libusb-0.1.so.4.4.4: Read-only file system
ln: /usr/lib/libwrap.so.0.7.6: Read-only file system
ln: /usr/lib/libxml2.so: Read-only file system
ln: /usr/lib/libxml2.so.2.7.2: Read-only file system
ln: /usr/lib/libywgui.so.1.0: Read-only file system
ln: /usr/lib/libz.so.1: Read-only file system
ln: libpcap.so: Read-only file system
ln: /usr/lib/libfreetype.so.6: Read-only file system
ln: /usr/lib/libfreetype.so: Read-only file system
ln: /usr/lib/libywgui.so.1: Read-only file system
ln: /usr/lib/libywgui.so: Read-only file system
ln: /usr/lib/libxml2.so.2: Read-only file system
ln: /usr/lib/libxml2.so: Read-only file system
ln: /usr/lib/libwrap.so.0: Read-only file system
ln: /usr/lib/libwrap.so: Read-only file system
ln: /usr/lib/libpcap.so: Read-only file system
ln: /usr/lib/libcfont.so.0: Read-only file system
ln: /usr/lib/libctutils.so.0: Read-only file system
ln: /usr/lib/libconsole.so.0: Read-only file system
ln: /usr/lib/libbmp.so: Read-only file system
ln: /usr/lib/libbmp.so.0: Read-only file system
ln: /usr/lib/libbmp.so.1: Read-only file system
ln: /usr/lib/libcairo.so: Read-only file system
ln: /usr/lib/libcairo.so.2: Read-only file system
ln: /usr/lib/libcurl.so: Read-only file system
ln: /usr/lib/libcurl.so.4: Read-only file system
ln: /usr/lib/libdirect.so: Read-only file system
ln: /usr/lib/libdirect-1.4.so: Read-only file system
ln: /usr/lib/libdirect-1.4.so.0: Read-only file system
ln: /usr/lib/libdirect-1.4.so.1: Read-only file system
ln: /usr/lib/libdirect-1.4.so.5: Read-only file system
ln: /usr/lib/libdirectfb.so: Read-only file system
ln: /usr/lib/libdirectfb-1.4.so: Read-only file system
ln: /usr/lib/libdirectfb-1.4.so.0: Read-only file system
ln: /usr/lib/libdirectfb-1.4.so.1: Read-only file system
ln: /usr/lib/libdirectfb-1.4.so.5: Read-only file system
ln: /usr/lib/libfreetype.so: Read-only file system
ln: /usr/lib/libfreetype.so.0: Read-only file system
ln: /usr/lib/libfreetype.so.6: Read-only file system
ln: /usr/lib/libfusion.so: Read-only file system
ln: /usr/lib/libfusion-1.4.so: Read-only file system
ln: /usr/lib/libfusion-1.4.so.0: Read-only file system
ln: /usr/lib/libfusion-1.4.so.1: Read-only file system
ln: /usr/lib/libfusion-1.4.so.5: Read-only file system
ln: /usr/lib/libgif.so: Read-only file system
ln: /usr/lib/libgif.so.0: Read-only file system
ln: /usr/lib/libgif.so.4: Read-only file system
ln: /usr/lib/libgtk-directfb-2.0.so: Read-only file system
ln: /usr/lib/libgtk-directfb-2.0.so.0: Read-only file system
ln: /usr/lib/libjpeg.so: Read-only file system
ln: /usr/lib/libjpeg.so.0: Read-only file system
ln: /usr/lib/libjpeg.so.62: Read-only file system
ln: /usr/lib/libpng12.so: Read-only file system
ln: /usr/lib/libpng12.so.0: Read-only file system
ln: /usr/lib/libpng.so: Read-only file system
ln: /usr/lib/libpng.so.0: Read-only file system
ln: /usr/lib/libpng.so.3: Read-only file system
ln: /usr/lib/libst2fx.so: Read-only file system
ln: /usr/lib/libst2fx.so.0: Read-only file system
ln: /usr/lib/libst2fx.so.1: Read-only file system
ln: /usr/lib/libtiff.so: Read-only file system
ln: /usr/lib/libtiff.so.0: Read-only file system
ln: /usr/lib/libtiff.so.1: Read-only file system
ln: /usr/lib/libz.so: Read-only file system
ln: /usr/lib/libz.so.0: Read-only file system
ln: /usr/lib/libz.so.1: Read-only file system
ln: /usr/lib/libywxml.so: Read-only file system
ln: /usr/lib/libywxml.so.0: Read-only file system
ln: /usr/lib/libywxml.so.1: Read-only file system
ln: /usr/lib/libopera.so: Read-only file system
ln: /usr/lib/libopera.so.3.0: Read-only file system
ln: /usr/lib/libywnative.so: Read-only file system
ln: /usr/lib/libopera_hbbtv.so: Read-only file system
ln: /usr/lib/libdsmcc.so: Read-only file system
cp: can't create '/etc/passwd': Read-only file system
rm: can't remove '/var': Read-only file system
ln: /var: File exists
mkdir: can't create directory '/var/': No such file or directory
ln: /var/empty: No such file or directory
ln: /etc/inadyn.conf: File exists
$Starting sshd:/usr/sbin/sshd: error while loading shared libraries: libwrap.so.0: cannot open shared object file: No such file or directory
ok
ln: /etc/resolv.conf: Read-only file system
ln: /etc/directfbrc: Read-only file system
ln: /usr/sbin/smbd: Read-only file system
ln: /usr/sbin/nmbd: Read-only file system
ln: samba: Read-only file system
tmp is exist
mkdir: can't create directory '/storage': Read-only file system
chmod: /storage: No such file or directory
/root/spark/Ad is exist
mkdir: can't create directory '/lib/firmware': Read-only file system
ln: /lib/firmware/rt73.bin: No such file or directory
ln: /etc/Wireless: Read-only file system
ln: /etc/wpa_supplicant.conf: Read-only file system
ln: /etc/ppp: Read-only file system
ln: /etc/vpn: Read-only file system
chmod: /dev/stapi: Read-only file system
sttbx_early_core: module license 'ST Microelectronics' taints kernel.
Disabling lock debugging due to kernel taint
* Looking for chipset model and version...
Load module stos_core [?]               by insmod (pid 692)
Load module stsys_ioctl [253]           by insmod (pid 694)
  STx7105 D detected
* Loading companions
mknod: /dev/stapi/lxload: File exists
cp: can't stat '/etc/samba/smbpasswd': No such file or directory
/etc/init.d/rcS: /root/autorun.sh: line 177: /usr/sbin/smbd: not found
/etc/init.d/rcS: /root/autorun.sh: line 178: /usr/sbin/nmbd: not found
Starting inadyn: ./vsftpd/vsftpd: error while loading shared libraries: libcap.so.2: cannot open shared object file: No such file or directory
autotest exist
rm: can't remove '/usr/local': Read-only file system
ln: /usr/local: File exists
mkdir: can't create directory '/var/': No such file or directory
mkdir: can't create directory '/var/': No such file or directory
ln: /var/log/lighttpd: No such file or directory
./ywapp.exe: error while loading shared libraries: libst2fx.so.1: cannot open shared object file: No such file or directory
^_^ spark is runnig ^_^
stlinux login:

Display More

anyone can help?
Thaqnks Stano

**ben361** · Nov 24th 2012

first post
introduce yourself here : Forum Gateway - Powered by DnP Firewall

gcstano · Nov 25th 2012

introduced. thx

**ben361** · Nov 25th 2012

read this thread maybe it is usefull
http://linuxsat-support.com/am…o-alien-2-stuck-boot.html

gcstano · Nov 25th 2012

I had read this article, did the command via putty but no success , that why i am posting a list from putty command line, if someone understand what is wrong. It says some errors writing var directory etc

**ben361** · Nov 25th 2012

have you try a resque image for the alien 2

gcstano · Nov 25th 2012

the receiver is blocked at boot ( init then boot) and doesn't matter what i press. i can access via putty to console, i have try the comand sequence from another thread but always finished with errors like you can see in log and nothing more. if i can load rescue image somehow via putty will probably help, but how?

gcstano · Nov 25th 2012

solved, problem is in command line for putty in line with network mask
"set bootargs console=ttyAS0,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:0037:04:15:00
ip=192.168.40.83:192.168.40.19:192.168.40.1:255.25 5.0.0:lh:eth0:off
stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=6000"

When you see the 'PK7105' prompt again, copy the following command without the quotes ("") and press ENTER:
"nboot.i 0x80000000 0 0x00100000 ;bootm 0x80000000"

thx

**ben361** · Nov 25th 2012

ok
so post 4 is useful
great that the problem is solved

welder1977 · Dec 23rd 2012

Hi I have the same problem my alien2 is stuck on INIT BOOT. can some one give me a heads up of what to do with putty and how to fix my problem please

**ben361** · Dec 23rd 2012

read this first :http://linuxsat-support.com/am…o-alien-2-stuck-boot.html

welder1977 · Dec 23rd 2012

how can I paste the command into PuTTY?

**ben361** · Dec 23rd 2012

i think the best way is contact your reseller.

**Robxxx7** · Dec 23rd 2012

Agree with Ben here .... if you are not sure how to paste the commands in then its best you not try the commands ... It will no doubt result in your box being bricked and then rather than have your reseller fix it for you, it will become an expensive paperweight

welder1977 · Dec 24th 2012

well im happy to type it in but on every site i have seen this on it is shown like this
set bootargs console=ttyAS0,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00*:06:37:04:15:00

ip=192.168.40.83:192.168.40.19*:192.168.40.1:255.255.0.0:lh:e*th0:off

stmmaceth=msglvl:0,phyaddr:1,w*atchdog:5000 bigphysarea=6000
These have a space or is this all one line?
Cheers

**h2014** · Jan 8th 2014

Hello Everyone, i also have a amiko alien 2 stuck on boot. im a complete newbie to amiko. BUT im still stuck. i get the error below.

Board: STx7105-PDK [32-bit mode]

U-Boot 1.3.1-g72483220 (Jan 17 2012 - 17:10:49) - stm23_0051 - YW_1.1.003-9-g7248322 overclock

DRAM: 256 MiB
NAND: Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
512 MiB
SPI: ERROR: Unknown SPI Device detected, devid = 0x1f, 0x46, 0x02
ERROR: Offset out of range (max=0xffffffff)
In: serial
Out: serial
Err: serial
Ident ic exist
Ident ic get stb id
IdentID : 0c 00 0a 00 00 08 01
PDK7105>
PDK7105> stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=6000
PDK7105> set bootargs console=ttyAS0,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:0037:04:15:00
PDK7105> 8.40.1:255.25 5.0.0:lh:eth0:off
Unknown command '8.40.1:255.25' - try 'help'
PDK7105> 000
Unknown command '000' - try 'help'
PDK7105>

do i need to download anything before trying putty? not sure what im doing wrong! im not sure what files i need to download and upload to box.

helcer · Jun 9th 2015

same problm - not working for me :-(

has anyone an idea?
is it possible to Flash the alien2 by Serial - rs232?

- - - Updated - - -

see here the logfiles:

For bigger images klick here:
http://img5.fotos-hochladen.ne…/sparkboot12lqgmh1u7b.jpg
http://img5.fotos-hochladen.ne…/sparkboot2ci4q76eh9g.jpg
http://img5.fotos-hochladen.ne…/sparkboot3k3dj4lm7fu.jpg

**joeuser** · Jun 9th 2015

Which "same problem" since there are actually a few different problems listed in this thread?
Do you have the output from the serial console?
Have you tried to boot to Spark by using the commands in the link to the other thread?

Flash by serial or flash from the serial console? You can flash by serial, but it is not as easy as USB, TFTP, or NFS.

Your best bet is to try to first try to install the older version of Spark which contains a U-Boot, then upgrade Spark, then try installing an Enigma2 image.

So you updated your post before I finished answering... :)

Looks lie you do not have any of the same problems from this post - your box is booting ok into enigma2, but there is some problem with enigma2. What image did you flash? Is this first boot of the image, or was it working ok before and then stopped?

helcer · Jun 9th 2015

joeuser

hi, as i restarted from hdmu to spark (in the menu of hdmu) the box stops at "boot"
nothing works and i cant flash by usb or online because i dont come to the option ...force .....
all restarts failed

this is what happens: https://www.youtube.com/watch?v=oUgwzbMalXM

**joeuser** · Jun 9th 2015

Ok, I looked more closely and see you are trying to boot to Spark. On my box, for Spark my bootargs has "bigphysarea=7000". Can you try it with this change?

Amiko Alien 2 Won`t Boot

Spark STI 7162 Support

Participate now!

Share

Similar Threads

Gigablue UHD UE 4k ram

amiko alien 8900 no spark mode

AMIKO ALIEN SHD 8900

SHD 8900 help