Keep getting this message on quiet a number of channels mainly on 7west 26east and 13east, these are FTA channels I'm trying to view and snr shows 80+% I have tried updating my XML file but still getting the same message, any thing else I can try to view these channels, any help will be much appreciated :)
Sid not found in pat help
- chucknorris666
- Thread is marked as Resolved.
-
-
Quote
have tried updating my XML file but still getting the same message
Did you rescan 7west, 26east and 13east after adding the satellites.xml file ? A rescan or adding a new channel list should sort your problem buddy..
-
Yes mate I did rescan. Still same problem, going to try reflash later tonight see if that will sort it out.
-
Will I need to add a new satellite XML file if I'm flashing the latest vix image ?
-
Try the new catseyes out today i have no issues with it
-
Iv tried em mate, literally pulling my hair out now :( hears what iv done so far,
Installed latest XML file (no luck)
Checked f connectors and wires (all ok)
Fresh flash latest vix 3.0 build 654 no back up
Set up tuners again
Tuner A
Simple
Single
28.2E
Tuner B
Simple
Positioner
Long & lat (from dish pointer)Installed latest catseye settings 3-4-13
(Still same message on quiet a few channels)
Service Not Found!
(SID not found in PAT) -
if all else fails ,,,get an older previously working settings ipk , ftp it across ,
restart then check the channs then try another settings file,,
there are many here on site..
no need to lose your hair about it..unless you really want to.. -
Lol I gave up last night and had a few beers instead
Will try old settings that use to work later today.
I'm wondering if maybe I have a line of sight issue as they has just built some new houses over the road that are quiet tall as most of the sats are fine just seems to be mainly 7west and 26east, but if this is the case why do I still have good snr ???
-
Iv tried em mate, literally pulling my hair out now :( hears what iv done so far,
Installed latest XML file (no luck)
Checked f connectors and wires (all ok)
Fresh flash latest vix 3.0 build 654 no back up
Set up tuners again
Tuner A
Simple
Single
28.2E
Tuner B
Simple
Positioner
Long & lat (from dish pointer)Installed latest catseye settings 3-4-13
(Still same message on quiet a few channels)
Service Not Found!
(SID not found in PAT)You may try to make your own xml file by going to www.satellites.xml.eu and choose only the satellites you need this way you get fewer similar frequencies and load this xml file in your box and see if it helps.
-
You may try to make your own xml file by going to www.satellites.xml.eu and choose only the satellites you need this way you get fewer similar frequencies and load this xml file in your box and see if it helps.
Thanks for the useful post but can you please post an introduction when you are next on the forum and follow the rules
steve
-
chucknorris666 did you manage to sort the prob mate as I seem to have same issues?
-
chucknorris666 did you manage to sort the prob mate as I seem to have same issues?
This is an interesting read about the subject : http://linuxsat-support.com/vu…ound-pat-vu-tutorial.html
I would suggest you try out what is posted in post #9 here in this thread...
Enigma2 DVB - FBC - USB Tuners
Enigma2 Tuners. Articles, Downloads and Support for DVB-S2 Tuners, DVB-S2X Tuners, DVB-C/T2 Tuners, DVB-C USB Tuners, DVB-T/T2 USB Tuners, DVB-T/T2/C USB Tuners, FBC Tuners, and Tuner Drivers.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!