Problems excluding sly uk from other peoples C-Lines , DOin My Nut :-)

There are 17 replies in this Thread which was already clicked 3,434 times. The last Post () by ddaddy.

    Ok i have about 10 shares in VU+ box CCam 2.1.3 with my Sly local on an N Line from Debian Oscam Server with 256 trick to fake local!


    HOWEVER


    When i change channel sometimes my VU+ will decide to take a feed from someone else on hop1/2 ?????? (never used to!)


    so say my c-line is :


    user.dyndns.org 12345 user pass


    when i put this below shouldnt ccam block requests to 0963 (sly) from that user because i still seem to pick up from there line somehow???:


    user.dyndns.org 12345 user pass { 0963:0 }


    am i missing something or is the 0963:0 wring , have also tried 0963:000000 and still it does not block!


    Cant get the lines to block 0963!


    Thanks guys

    I'm in a similar situation where I want to block BoxNation from my CCcam peers but nothing I've added after the C line seems to work..


    I'm really not sure if you can do it yourself....the peers might have to do it on their F line?


    Theres something else a miss though...no way should your server be preferring ECM's from a hop 1 or higher over your hop 0!!

    sandman i agree , i have changed nothing, i have remove anticascading from debian as i have 4 flines pulling codes from main user on server, the channels clear when i # all other c-lines, as soon as i enable the other lines its all over the place, changed the n-line to a c-line from oscam server and seems a little better but also want it so i know my local is off straight away! :-)

    You are trying user.dyndns.org 12345 user pass { 0963:0 } ?


    You need to add 'NO' after the pass (or yes if you want to accept emm's):


    user.dyndns.org 12345 user pass no { 0963:0 }

    Glad you got it sorted Deerhunter. As soon as cccam gets the wrong syntax in a line, it ignores the rest of it.


    Sandman, not entirely sure without checking my config, but try { 0963:channel caid:0 }

    Quote from ddaddy

    Just read the original cfg info and it says that is how its done!
    { caid:id:0 }


    I've tried all of these to block BoxNation -


    C: address port username password no { 0963:C5CB }
    C: address port username password no { 0963:C5CB:0 }
    C: address port username password no { 0:0:2, 0963:C5CB }
    C: address port username password no { 0:0:2, 0963:C5CB:0 }


    no dice so far!

    Quote from ddaddy

    Try restarting cccam after putting the line in.
    Remove all other lines to make sure they're not cleared by another one.


    Doesn't amending and uploading cccam.cfg restart everything? I always get a freeze so assumed it was all restarting!


    I've even rebooted after...still no joy!


    Time wise it would be cheaper to subscribe :tire:

    Quote from Ten Below

    Its in the CCcam.cfg file lads



    Code
    #
#C: <hostname> <port> <username> <password> <wantemus> ( { caid:id(:uphops), caid:id(:uphops), ... } )
#


    Try and get your peer to block it on the fline, you cannot block sids on the cline only providers.


    Thanks for the confirmation....too much bother to message 5+ peers asking them to block a single channel...I'll just leave it!

Your resource for CCcam softcam

Find downloads, configuration files, setup tutorials, and community support for card sharing and server management. Master CCcam configuration and card sharing. Access dedicated support, step-by-step tutorials, config files, and downloads for your Enigma2 setup.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login