Είναι oscam ή oscam-emu αυτό που τρέχει;
Posts by nautilus7
-
-
Πιο πιθανό είναι συμβαίνει αυτό που λέει ο georgeflu.
-
Are you using a translator to write in Greek???
Εδώ είναι η ρύθμιση για το CRC στον κάθε reader: https://drive.google.com/open?…hDS2t7QFJAVK7V_r5w88cdy_X
Δεν υπάρχει μέσα στο oscam.server, γιατί απλά είναι στην default ρύθμιση. Οι default ρυθμίσεις δεν γράφονται αρχικά.
Δεν καταλαβαίνω αυτό που γράφεις για τη λήψη των CW από την κάρτα... Τα CW λαμβάνονται από την κάρτα όπως είναι με μια συγκεκριμένη διαδικασία. Στο oscam δεν έχει αλλάξει κάτι ως προς αυτό. Κατόπιν διορθώνονται ή όχι τα CRC bytes από το oscam αν είναι επιλεγμένες οι αντίστοιχες ρυθμίσεις και στέλνονται στους descramblers.
-
Quote
You can try to ignore the CRC check for all CAIDs and PROVIDs, but then all CWs will be sent to the card (it may also cause the decoding card to malfunction, for some satellite providers):
disablecrccws = 1 - http://www.streamboard.tv/wiki…scam.server#disablecrccws
... instead of the entry :
disablecrccws_only_for = CAID:PROVID,PROVID,PROVID,...;CAID:PROVID... - http://www.streamboard.tv/wiki…er#disablecrccws_only_for
WARNING ! The instructions on the internet indicate that this entry must be entered in the "oscam.server" file under the "reader" section. However, this setting belongs to the "oscam.conf" file under the "global" section. Is it some bug or some modification from another versions. However, the latest Oscam common versions must have this setting stored in the "oscam.conf" file and not in the "oscam.server" file.
Το μήνυμα που παραθέτεις είναι τίγκα στις ανακρίβειες...
Τα κλειδιά (CW) δεν στέλνονται στην κάρτα. Τα κλειδιά διαβάζονται από την κάρτα και στέλνονται στο hardware του δέκτη που είναι υπεύθυνο για την αποκωδικοποίηση του καναλιού (descramblers).
Επίσης οι ρυθμίσεις που αναφέρεις (disablecrccws και disablecrccws_only_for) είναι διαθέσιμες και για κάθε reader (δηλαδή μέσα στο αρχείο oscam.server), αλλά και γενικά για όλο το oscam (global) μέσα στο αρχείο oscam.conf.
-
Δεν νομίζω να ήταν αυτό το πρόβλημα.
-
anestis1956 λογικά δεν βλέπεις [streamrelay] στο oscam.conf γιατί oi προεπιλεγμένες ρυθμίσεις (default) δεν γράφονται. Πήγαινε στο webif και στο config θα βρεις σίγουρα επιλογή streamrelay.
Για τα powervu δεν χρειάζεται streamrelay με τον δέκτη που έχεις. Οπότε απενεργοποίησέ το, εκτός και αν το θες για άλλα κανάλια (compel, rosscrypt), όπως σου γράφει ο medousa89. Οπότε σε αυτή την περίπτωση δες πώς να το ρυθμίσεις.
-
Every AFN channel have this problem. To lose video I have to switch from a working afn channel to another. To make the video come back I have to go to whatever different from an AFN channel (recording, fta or encrypted channel) then go back to the AFN channel.
Unfortunately I cannot say if it is an update issue since I'm using oscam-emu for the first time (only plain oscam till now).
Oscam log arriving in the next minutes...
I am 99% sure this is a driver problem. Post in the openatv forum or the github repository and ask them to ask the manufacturer for a fix.
-
Can you make a log with debug 128, like I described before, but this time when you zap at an AFN channel with no video, start a recording. I want to see if there is something in the log at that time.
Is this issue present for a long time? Did you make an update, either in oscam or in openatv and then I showed up? Maybe it's a driver issue.
I can't see how it is an oscam problem though. Everything seem OK in the logs. Every AFN channel is the same, so if there was a problem in oscam, then every AFN channel should have the same problem.
Please also post your complete config folder (just make sure you remove any private info from your oscam.server)
-
I tend to believe that it might not be oscam-emu's fault. Try if the recording is ok.
-
A video will not help either...
Can you tell which channel change in your last log triggered the issue?
Can you also try this: Change channels until you get again a blank screen (no video) with AFN.
At that point start a recording for that channel with no video. Does the recorded file play with video on a PC?
-
I don't see anything wrong in the log.
oscam seems to descramble both audio and video every time you tune to an afn channel.
-
rockerduck your log in not good. It's very small and does not contain any useful info.
I will need a new log with debug 128. Set initial debug level to 128 and log size to 3000KB. Then restart oscam and do the whatever you need to make the problem appear.
Also, try with extended_cw_api set to 1, instead of 2. I am not sure this do any difference though.
Does your receiver open the powervu channels in 0.8W of 4.8E?
-
Άλλο και τούτο πάλι... Τι δουλειά έχει το Viaccess με το stream relay;
-
ΟΚ, άρα μάλλον υποψιάζομαι κάποιο disablecrccws στο global config...???
-
Δεν ξέρω αν το συγκεκριμένο ανοίγει (με card sharing) ή όχι, αλλά όπως βλέπεις κι εσύ γράφει "found".
Άρα ή έχεις κάποιο θέμα με τις ρυθμίσεις σου (πρέπει να τις δούμε) ή το συγκεκριμένο δεν ανοίγει καθόλου (ούτε με CS).
-
Perhaps if you could write proper English, you would have got a response...
What does mean "ok on powervu"?
What does mean "ok on oscam"?
What does mean "oscam line"?
Where is a log showing your problem?
-
For starters, rescan the transponder, in case they are doing changes in the channels.
-
I removed cacheex from your emu reader (plus some unneeded options):
Code
Display More[reader] label = emulator protocol = emu device = emulator disablecrccws_only_for = 0E00:000000 caid = 0500,1801,0604,0E00,1010,2600 detect = cd ident = 0500:000000,023800,021110,007400,007800;1801:000000,007301,001101,002111;0604:000000;0E00:000000;1010:000000;2600:000000 group = 1 emmcache = 2,1,2,1 emu_auproviders = 0604:010200;0E00:000000;1010:000000
-
να ρωτησω αν γνωριζει κανεις αν σε openblackhole image σε vusolo Μπορω να σεταρω το osca-emu να παιζει stream relay.γιατι απο οτι ειχα δει στο blackhole image δεν γινεται να παιξουν τα P@wer vu διοτι δεν υπαρχει η επιλογη για ecm fix.απο οτι ειδα ομως στο openblack hole υπαρχει η εντολη απλα δεν μπορω να δω απο που να κατεβασω to oscam emu...καμια βοηθεια?
Αφού δεν γνωρίζεις πώς να εγκαταστήσεις το oscam-emu χειροκίνητα, γιατί απλά δεν το εγκαθιστάς μέσω των feed του image; Αν δεν υπάρχει, απλά άλλαξε image.
-
Μπορειτε να μου προτεινεται κατι να παρω αξιζει αυτος στα 49 ευρω απο cosmodata μου ειπαν οτι παιζει κανονικα ccam και εχει κ iptv απλα θελει καποιες διαδικασιες ευχαριστω εκ των προτερων....
Για μένα, αν θες το κεφάλι σου ήσυχο πάρε κάποιον enigma2 με καλό support (π.χ. edision που γνωρίζω ότι υποστηρίζονται πολύ καλά), αλλά βέβαια ανεβαίνεις σε υπερδιπλάσιο κόστος.