Posts by paulus

I feel a sense of achievement at finishing my first BH (2.0.4) build. I just have two (minor) issues that I would love to resolve - but need your help.

1. My ecm time display (I am using CCam 2.1.3 and CCcamINfo 1.3) shows ecm time as "nan" - how do I get it back to secs
2. How do I get CoolTVGuide (6.4.0) to start (EPG button) in a Cool TV Guide rather than a single. The configuration menu only seems to have the option of "Start Cool Info Guide with EPG button yes/no".

All help is appreciated.

I would like to add this to my BH 2.0.4 build, but where can I get it, and how do I install it?

Many thanks (still learning).

Yes, I had installed the version from TSpanel/Tunisiasat Vuplus addons/plugins. If that is the problem then I will strike it off my list of "must haves" and try again. I found that a number of other actions caused green screens and restarts, so I have abandoned just now, gone back to my backup of 2.0.3 and will try again - probably tomorrow. One further question, most addons require a GUI restart, must this be done after each one or can I install a few than do a restart?

Having lived off the back of Ten Belows backups (BH2.0.2 and 2.0.3) since first getting my Solo2, I decided to be brave and build 2.0.4 myself. All going well, downloaded and installed addons via TSpanel etc. However, somewhere along the way my Green button no longer brings up my addon menu. Any ideas as to what I may have done, and more importantly, how do I get it bacK?

Many thanks. Into it now, but is there only German content? The menu is in German, and each of the files I have played so far are also in German audio.

Pressed "Menu" to see what configurability I have (language, delete certain servers, etc) but was then asked for a PIN?? Anyone know what the PIN is?

SORTED: Found it - SerienFilm (extension)

After a rebuild I have lost one of my plugins or extensions which put my recordings into folders. I have looked through the usual sources but cannot find it (and I cannot remember its name). Can anyone help?

Decided to update my channel list with catseyes latest. Edited as usual then tried to load via VCC (a form of DCC I guess). It loaded a few files then gave a message "OOOPS: ftruncated". Not knowing what went wrong tried again and failed on the first file. Tried again to reload the previous version - failed again on first file. Assuming that I must have a corrupted file during the download I ftped into /etc/enigma2 and deleted all of the files that appeared to be from the channel set. Tried again - success!! Only problem is that now all of my channels are greyed out - message says check tuner config. Tuner config is half right: Tuner A is positioner USALS, and Tuner B is simple but with no satellite (should be 28.2E) - cannot configure it - says nothing connected.

I guess I must have deleted one file too many - but how do I recover without a reload and start again?

Just a thought . . . have you uploaded a channel list?

BH 2.0.3 was a clean install via Ten Below's backup, it was just that the backup had no cam hence me installing CCcam etc.

Will give it a go - but cannot report back on that until tomorrow. Wondering whether I should also remove the oscam/cccam since not in use?

Since upgrading I have a daily problem that was not there before (2.0.2 and in both cases Ten Belows backup as start point). Possibly giving too much info but since I don't know the cause I will give as much as I can. I have CCcam2.1.3 installed as well as an oscam/cccam (but using only CCcam in client mode) as well as CCcam Info 1.3. Each night I do a timed epg update, followed by a deep standby. Now every morning when brought out of standby everything works fine for a short time (less than 15 mins) then the problem: picture freezes, looks like server gone down, go into CCcam Info - select server - no response from CCcam Info, so unable to see whether/which server is up/down. Restarting UI does not seem to sort the problem but rebooting does - then flawless operation for the rest of the day.

Any ideas??

Quote

Oh, and is ten Barlow Gary Barlows brother?

I thought he was Ken Barlow's love child!

I am upgrading my Solo2 to BH 2.0.3, and for the life of me cannot find AutoTimer, and CCcam Info 1.3. Can anyone point me in the right direction. Many thanks.

BLOW ME!! That works. Well done thatfellow!

Appears not to be the case, since my N: line is at the top, but my C: line is always preferred. However I am using oscam/cccam 2.1.3 (I think - using Ten Belows backup) - so what is the 256 trick?

Is there a way of "prioritising" lines in CCcam.cfg? I am using BH 2.0.2 with two lines - one C: and one N: - however since the N: line only provides for one package I want it to have priority when that package is being viewed. Currently the C: line is always active even though the N: line appears first in the list.

Further to the above, I am using BH2.0.2E on a Solo2. Which of these goes in /usr/lib/enigma2/python/plugins/extensions?

Found it! Yes I have a plugin which provides the CCcam info - exactly what I was looking for. Many thanks.