Posts by harley22

Hello. Just to repeat - if I flash my box with the Vix 3.0 image, will I lose Oscam and cccam and have to put them back in again?

I still have not ben able to get my box working properly and I have had it six weeks now.

I know how to flash the box but don't want to lose any plugins I have.

Please can you help again and if possible, help me set the thing up. It may need help from someone as i am not confident enough to do it myself and am completely lost by this that everyone else seems to be able to get their entitlements byt not me.

Thanks and I look forward to hearing from you.

Current image is 4D Enigma 2 but will I lose Autobouquets and 7 Day EPG and oscam/cccam if I reflash.

If so, I will need someone to help me in real time.

Thanks again in advance.

After all that, localhost does not work for me. 127.0.0.1 will not connect.

I cannot even get into thaton my browser.

I have now changed the localhost to 127.0.0.1. I did have ,s instead of full stops - will have to reboot first.

My box is TM Twin OE with Enigma 2 4D image.

As I say it's al working but not reading entitlements.

OK it would appear that Oscam 1.00#6829 does NOT work with the cccam.cfg CONFIGURATION FOR ** s**** as described earlier.

This does not make sense to me. Adding 127,0,0,1 to the hhttpallowed did nothing for me.

My cardreader is acting just like a non-linux box and I am getting very frustrated about it.

I cannot uninstall anything on the box - it is not possible as far as I know. Nor can I reflash the box as I am not sure then if it will work afterwards.

Also I have never managed to get Oscam 1.20 working. Could this be a factor? Not sure if 1.20 is compatible with *** UK.

Please advise. Thanks.

Despite thata no luck I'm afraid. The cccam 2.1.3 server is working but not oscam server via my browser.

I have now put it back to 8888 for now.

this is really driving my mad - this should be easy but it is anything but.

If someone can help me with TeamViewer, please can you do so. Thanks.

I have added the 127,0,0,1 into httpallowed now but my n: line - this must vary - what would that be? Thanks.

I will by the way, restart my box and see what happens? I only have an F: line in cccam at present. I also have a refee4cne to cccam 2.1.4 in .conf, do I need to change this to 2.1.3. Thanks.

What is the difference if you put debug = 255 underneath? And, do I need a username and password?

thanks. So is it just this bit

httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255

I seem to have missed out 127,0,0,1,

Would I be right? If I add in httpallowed = 127,0,0,1, prior to 192.168,0,0-192.168.255,255

will it work then? Does the port HAVE TO BE 8888? I have never had that working except when someone did it for me, but as soon as I rebooted my box it disappeared.

And, do I need admin for the httpuser and password?

Thanks.

Thanks. So why is port 16002 not working which is where the oscam port should be in my configs? I just get "Unable to connect. Can't Establish a connection to the server at ...:16002".

So if Oscam is running the card, why can't I get this on my PC?

Just to also say that the N line in the cccam.cfg for the configs in the ** S**** file says 10001, not 16001. I wonder is this why it will not work. Thanks.

I have tried to use the configs set out in a file posted here further back but when I did put this on my box, it stopped clearing the channels. A few of them had the oscam label appear on screen as if it was opening the channel but no luck.

Some channels were ignored completely. So I had to put the cccam.cfg file back to how it was and then it started working again.

this does not make sense. Can anyone else help? Without that I still cannot see the entitlements.

Thanks in advance.

Indeed but I still cannot get it to work so I can see the entitlements. The webif is already on my box.

Not sure if I know what you mean by that? My web info details - Where do I find that?

The webif part is as follows. I cannot get port 8888 working on my PC so don't understand. How do I get it to work please? It is definately Oscam that is working on my receiver but cccam is ticking so I am lost. If yu can help I would be most grateful.

Thanks.

[webif]
httpport = 8888
httpuser =
httppwd =
httprefresh = 5
httphideidleclients = 0
httpallowed = 192.168.0.0 - 255.255.255.255
debug = 255

Thanks. I have no password there - and I thought the clock speed was 3570000 not 6000000 plus.

Not sure what I should leave out of the config files if I want to display them. Please see pm box. Hope you can help me further.

At present, I cannot get port 8888 working at all, bt 16001 is working but won't show any entitlements.

The card reading data is showing in "oscam.mem" and a file "ecm.info" shows current channel ecm data.

Thanks for your help.

Sorry I am confused. Is it Oscam or CCCam we are talking about? I thought you could use Oscam to get entitlements but I don't see any - not even a list of data for entitlements. Please can you help? I currently have a single *** card being read in the machine via Oscam.

Thanks.

Sorry - *** UK 0963. Thanks.

Is there any way of finding out how long it will be before your card needs an entitlement? I have so far not been able to get entitlements working. the ECM length appears to depend on the channels themselves or at least the packages.

Please can someone explain which PID I need to look in to find out what date my card will stop working? And, a length of for example 5F, this is 95 characters long. Whcih PID is this foudn on and is the date contained in there? If so, what do I look for?

Thanks.

So if you ae not using cccam, and only oscam, will you continue to get entitlements. BTW how do you read the entitlements table? -

1: on the Twin OE
2: on a PC

Thanks.

Quote from master G

Set the au [account] to match the [reader] label = suk1

Code

[account]
user = linuxsat1
pwd = apassword
caid = 0963
group = 1
cccmaxhops = 1
au = [COLOR='#FF0000']suk1[/COLOR]

Hi there. Just wondered where you have [account] what goes in place of this in the configuration? All the config files have something with square brackets around at the top of each part and I am not sure if these need changing and if so, what to.

I now have a Twin OE but want to use my own card in it with auto update. If anyone can help please get in touch.

And thanks for an easy to read site. Thanks in advance.