FBC tuner

You are taking too long to respond. If you want help, please answer the questions asked of you and provide the information requested.

Here is a sample HARDWARE configuration diagram. I am guessing as you are not forthcoming with response.

pasted-from-clipboard.png

Issue this command and upload the file it creates in /tmp directory

cat /etc/enigma2/settings | grep config.Nims > /tmp/mytunerconfig.txt

Your LNB has 24 SCR. If you connect the Hardware correctly and configure software to match, you can access 16 Transponders independently. If each transponder has 8 channels, you can theoretically record/view/stream 128 channels. This is subject to network bandwidth and encryption that the channels use. There are bugs that the some images have when you get over 40 channels though!

Please upload a wiring diagram/picture. This is the 3rd time I am asking.

I think we have resolved this remotely. Hopefully feedback will follow.

The wiring was changed to following:

pasted-from-clipboard.png

Wire from LNB goes to splitter.

He has one wire from splitter to top slot, of 1 module. Tuner A

He has another from splitter to top slot, of 2nd module. Tuner I

He has another wire from the splitter to another receiver.

Tuner A has got independent signal supply, so the connected option is set to "No"

Tuners B-H do not have an independent signal supply, They are getting it from Tuner A. So said yes to "connected" and selected Tuner A. They all have unique SCRs

Tuner I has got independent signal supply, so the connected option is set to "No"

Tuners J-P do not have an independent signal supply, They are getting it from Tuner I. So said yes to "connected" and selected Tuner I. They all have unique SCRs

The Solo 2 had an SCR that was being used by the Duo 4K SE. So that was changed to SCR 17

Here are some guides.

Article

Guide to using Unicable

Guide to using Unicable

A guide to explain possible usages of Unicable/Unicable 2 LNBs. Unicable 2 is also known as JESS
I would like to start off by stating that Unicable LNBs do not need specific tuners. You can use them with a "normal" receiver like: Technomate Nano SE, Vu Solo 2, Vu Duo, Xtrend 8000, Gigablue Quad, Mutant HD51 In the old days, LNBs generally came with a single port. You could only connect to one receiver. Then came Quad LNBs which had four connections, Octo LNBs with…

abu baniaz

Jan 6th 2019

Article

GT-Sat GT-dLNB1DY and tuner configuration

Below is a guide for configuring the GT-sat Unicable LNB with FBC tuners with only one wire and no splitters

ABM and CrossEPG require sole control of a Tuner, so you will get blackouts while they run.
(As a reminder, FBC tuners and Unicable are two separate technologies.
You can use Unicable LNBs with non-FBC tuners. Eg Dreambox 500, Vu Solo 2, Technomate Nano 3t combo
You can use an FBC tuner with universal (normal) LNBs.
FBC with unicable offers more than FBC with universal.)
For this guide,…

abu baniaz

Jan 6th 2019

Article

Unicable tuner configuration for Non-FBC tuners

Unicable tuner configuration for Non-FBC tuners:

It should be something similar to this.

Type of LNB/device = SCR (Unicable/Jess)

SCR (Unicable/Jess) type = LNB. Unless you are using a Unicable/Jess switch.

Manufacturer = self explanatory

Model = self explanatory

Position = leave this as 1. (Some LNBs can be programmed and used in combination)

Repeat for every tuner. Make sure that you do not re-use the same user band channel. This applies to all tuners accessing the LNB, even if they…

abu baniaz

Jan 6th 2019