Oscam server setup guide - Raspberry Pi from scratch.

in your reader config you still have your device as internal what cardreader are you trying to use with the Pi? if its smargo then you need to configure the reader in oscam.server to reflect that

thank you for helping me.

Yes i have smargo in one of two USB in raspi.

how to reflect this

this is what i'm was using in dreambox

[reader]
Label = ***IT
Protocol = internal
Detect = CD
Device = /dev/sci0
group = 1
emmcache = 1,1,0
boxid = ******
blocknano = all
mhz = 368
cardmhz = 368
blockemm-u = 1
blockemm-s = 1
blockemm-g = 1
blockemm-unknown = 1
blockemm-bylen = 183,81

ok you need to go to the web interface and select readers from the top of the main page then select scan usb you should see something like this...

Bus 001 Device 005: ID 0403:6001 Future Technology Devices International, Ltd FT232 USB-Serial (UART) IC
iProduct 0
iSerial 3 Reader 224

Now in your oscam server file you need to edit it to reflect the Bus and device like this....

Label = SLY_uk
Device = 001:006
Protocol = smartreader

where the device + is you put your address so in this example it would be Device = 001:005

Reboot server and check

ttyUSB0

o.k. thanks

thanks for helping me...

quite difficult to set all and make it work..

is possible to connect to oscam from cccam client using C: lines?

Thanks now my smartcard is working but a have other problems.
thisis my oscam status.

cccam: initialized (fd=5, port=12000)
2013/03/06 08:36:31 0 s Tivusat [smartreader] creating thread for device 001:004
2013/03/06 08:36:31 0 s loadbalancer: can't read from file /tmp/.oscam/stat
2013/03/06 08:36:31 0 s waiting for local card init
2013/03/06 08:36:31 197C80 r Tivusat [smartreader] Using 0x01/0x82 as endpoint for smartreader hardware detection
2013/03/06 08:36:31 1A00E8 h webif: decompressed 50857 bytes back into 150432 bytes
2013/03/06 08:36:31 1A00E8 h HTTP Server listening on port 8181
2013/03/06 08:36:31 197C80 r Found smartreader device 001:004
2013/03/06 08:36:31 197C80 r Tivusat [smartreader] Reader initialized (device=001:004, detect=cd, mhz=368, cardmhz=368)
2013/03/06 08:36:32 197C80 r Tivusat [smartreader] card detected
2013/03/06 08:36:35 197C80 r Tivusat [smartreader] ATR: 3F FF 95 00 FF 91 81 71 FF 47 00 54 49 47 45 52 30 30 33 20 52 65 76 32 35 30 64
2013/03/06 08:36:35 197C80 r Tivusat [smartreader] Init card protocol T1, FI=9, F=512, D=16, N=255
2013/03/06 08:36:35 197C80 r Tivusat [smartreader] Calculated work ETU is 8.70 us
2013/03/06 08:36:35 197C80 r Tivusat [smartreader] ATR Fsmax is: 5 Mhz, clocking card to wanted user cardspeed of 3.69 Mhz (specified in reader->mhz)
2013/03/06 08:36:36 197C80 r Tivusat [smartreader] detect nagra tiger card
2013/03/06 08:36:37 197C80 r Tivusat [smartreader] card system not supported
2013/03/06 08:36:37 197C80 r Tivusat [smartreader] Normal mode failed, reverting to Deprecated Mode
2013/03/06 08:36:40 197C80 r Tivusat [smartreader] ATR: 3F FF 95 00 FF 91 81 71 FF 47 00 54 49 47 45 52 30 30 33 20 52 65 76 32 35 30 64
2013/03/06 08:36:40 197C80 r Tivusat [smartreader] Init card protocol T1, FI=9, F=512, D=16, N=255
2013/03/06 08:36:40 197C80 r Tivusat [smartreader] Calculated work ETU is 100.81 us
2013/03/06 08:36:40 197C80 r Tivusat [smartreader] ATR Fsmax is: 5 Mhz, clocking card to wanted user cardspeed of 3.69 Mhz (specified in reader->mhz)
2013/03/06 08:36:41 197C80 r Tivusat [smartreader] detect nagra tiger card
2013/03/06 08:36:42 197C80 r Tivusat [smartreader] Resync error: readtimeouts 0/0 (max/min) us, writetimeouts 0/0 (max/min) us
2013/03/06 08:36:43 197C80 r Tivusat [smartreader] T1 Resync command error, trying to reactivate!
2013/03/06 08:36:46 197C80 r Tivusat [smartreader] ATR: 3F FF 95 00 FF 91 81 71 FF 47 00 54 49 47 45 52 30 30 33 20 52 65 76 32 35 30 64
2013/03/06 08:36:46 197C80 r Tivusat [smartreader] Init card protocol T1, FI=9, F=512, D=16, N=255
2013/03/06 08:36:46 197C80 r Tivusat [smartreader] Calculated work ETU is 8.67 us
2013/03/06 08:36:47 197C80 r Tivusat [smartreader] ATR Fsmax is: 5 Mhz, clocking card to wanted user cardspeed of 3.69 Mhz (specified in reader->mhz)
2013/03/06 08:36:47 197C80 r Tivusat [smartreader] card system not supported
2013/03/06 08:36:47 197C80 r Tivusat [smartreader] card initializing error
2013/03/06 08:36:47 0 s init for all local cards done
2013/03/06 08:36:47 0 s anti cascading disabled
2013/03/06 08:36:47 1A7798 c anonymous disconnected from 192.168.10.24
2013/03/06 08:36:47 1A5FE8 c client connected to 34000 port
2013/03/06 08:36:47 1A5FE8 c anonymous disconnected from 192.168.10.24
2013/03/06 08:36:52 1AADB8 c client connected to 34000 port
2013/03/06 08:36:52 1AADB8 c encrypted newcamd:34000-client 192.168.10.24 granted (tivu, au=on (1 reader))
2013/03/06 08:36:52 1AADB8 c user tivu authenticated successfully (CCcam)
2013/03/06 08:36:52 1AADB8 c AU disabled for user tivu
2013/03/06 08:36:56 1AC970 c encrypted cccam-client 192.168.10.24 granted (nagra, au=auto (1 reader))

Hi,
I manage to make it work.

I'm using c lines..

Is quick for now, i will check for few days...

by
kikan

All running for me now without any problems. Mustn't have waited long enough previously to test - all good now.

Running on the Pi is far more stable (it's rock solid) on the Pi rather than running on my Amiko Alien2 so the Amiko is now just a client off my Pi.

Thx for the tuturial -> installed it this weekend and it is running very fine...

When i first got the raspberry pi; i tried openelec (XMBC 12) with plugin oscam installed.
This also worked fine; i only could not use the cron commands to restart the Pi everyday...
Cron was activated but it simply did not work; only solution was manually rebooting wich i do not like...

So i decided this weekend to try this tutorial...

Hi,

I had a spare RPi so thought I would give this tutorial a go.

Worked like a charm and am running OScam fine - one thing I was not sure on was whether rebooting the RPi every day is necessary? I used to run OScam on my VU Duo for weeks/months on end with no issues so don't see why the Rpi should be any different. Is it because it has a slower cpu/memory or just as a precaution?

hello, i finish the script to make update

with putty type:

Quote

cd /var/local
nano oscamupdate.sh

past the script

Quote

#!/bin/bash

cd /usr/src
sudo rm -rf oscam-svn
cd /usr/src
svn co http://www.streamboard.tv/svn/oscam/trunk oscam-svn
cd oscam-svn
sudo mkdir build
sudo chmod 755 build
cd build
sudo cmake -DHAVE_LIBUSB=1 -DHAVE_PCSC=1 -DWEBIF=1 -DHAVE_LIBCRYPTO=1 -DWITH ..
sudo make
cd /var/local
sudo mv oscam oscam_$(date +%m-%d-%Y-%H:%M)
cd /usr/src/oscam-svn/build
sudo cp oscam /var/local/
cd /usr/src/oscam-svn/build/utils
sudo cp list_smargo /var/local/
cd /var/local
sudo chmod 755 oscam
sudo chmod 755 list_smargo

Display More

ctrl+o for save and ctrl+x for exit

Quote

chmod 755 oscamupdate.sh

and run it

Quote

./oscamupdate.sh

or setup your webif for run this script

@ musogeek : can you add it to the first post for oscam user who followed your post and a big thank you for your tutorial

If we are using just oscam, were do we add the clients? And are clients using C: lines or anu other. I have just tried to use ubuntu server with oscam/cccam, want to try this rasperry wich i think i awsome.

Quote from hdmm

thank you for is work good

but what version fo rasp this oscam-svn8641-i686-pc-linux-webif-libusb-pcsc-Distribution
I try oscam version 8349 thank you

I'm looking for a compiled version of oscam 8349 thank you

For what it's worth , this installations works also perfect on a CUBIEBOARD !!!

Thanks

Is the Pi stable? Can this conifg be run round the clock? Is it capable of running oscam with say, 10 partners?

I use Pcduino ... Pcduino is armv7 such as raspberry pi...i have installed Oscam with this guide (Oscam server setup guide - Raspberry Pi from scratch). I need to configure Oscam on server...and client? Their use CCcam normally? Thanks :D