Articles

Unicable tuner configuration for Non-FBC tuners

Unicable tuner configuration for Non-FBC tuners:

It should be something similar to this.

Type of LNB/device = SCR (Unicable/Jess)

SCR (Unicable/Jess) type = LNB. Unless you are using a Unicable/Jess switch.

Manufacturer = self explanatory

Model = self explanatory

Position = leave this as 1. (Some LNBs can be programmed and used in combination)

Repeat for every tuner. Make sure that you do not re-use the same user band channel. This applies to all tuners accessing the LNB, even if they…
abu baniaz
Like 2
0

Unicable LNBs and motorised dishes

Unicable LNBs and motorised dishes

A Unicable LNB is a technology which allows multiple users (or multiple tuners) to access satellite broadcasts over a single coaxial cable and eliminates the need for the numerous cables required by a conventional system. In order to satisfy all users of the system the dish must remain permanently orientated to the one satellite that all the users wish to receive programing from. If the dish were to move from its permanent orientation this would disturb the…
abu baniaz
Like 1
0

Unicable devices and tune failed messages

Unicable devices and tune failed messages


The default delay built into enigma2 between powering up an LNB/switch and sending tuning instructions is not sufficient for Unicable devices. This means from a cold start or first satellite service selection a "tune failed" message is displayed.

Unicable devices are digital devices. That means a finite amount of time is required to elapse for the Unicable device to boot, between being powered up and receiving the first instructions on what to tune.…
abu baniaz
Like 3
0

Tuner configuration setup for a Motorised dish using stored positions

This is a quick tutorial to show the tuner configuration settings for a Motorised dish setup without using Usals.

Tuner A is connected to the motorised dish,and is being used in "Advanced" setting.

The first screenshot shows page 1 of the settings and screenshot 2 shows page 2 where you will need to input you Long & Latitude settings for where you are. (You can use Dishpointer or Google maps to get this info)

USALS has been set to "No". For the dish motor to move to each sat position that…
mckee25
Like 5
2

Stored Position Tuner Setup

STAGE 1.

GOTO Main Menu \ Setup \ Service Searching \ Tuning
Press "OK" on "TUNER A"

http://img338.imageshack.us/my.php?image=40440488.png

Use L/R keys to change Configuration Mode to "advanced"
Move down to "SATELLITE"
Use L/R keys to select the satellite you want to add

http://img183.imageshack.us/my.php?image=41833411.png

Go down to "LNB"
Use L/R keys to select "LNB 1"
Next ensure "Diseqc Mode" is " 1.2"
(I left the others at the default setting's)
Scroll further down to "LOF" and set…
master G
Like 4
1

Solving the problem of the locale of language in some versions of enigma2

Solving the problem of the locale of language in some versions of enigma2
Attach two attachments to the attachments after decompressing them with the dcc program, the contents of which are moved to the next path

The first file named locale by the program dcc Move the file inside the file named po to the next path
usr / share / enigma2
All languages are included in the .poc file

The second file is named "Language" by the program dcc. Move the file named "Language.py" into the following path…
ahmed gazye
Like 4
0

PurE2 General Setup

PurE2 will be supported by yours truly, the only (or at least the first) person on Earth who previously wrote a comprehensive tutorial for Enigma2, CamD's, CS, streaming, playback and all the worts..
gorski
Like 9
33

PROTECT YOUR STB WITH SURFSHARK VPN SERVICE

How to use Surfshark OpenVPN in Zgemma STBs (H7 and 9 series) with PurE2 in order to protect your traffic and content of your STB, the easy but effective way!
gorski
Like 7
15

PiP (Picture in Picture) in PurE2

Since I was asked how PiP (Picture in Pictire) actually works in Zgemma STBs with PurE2, here is a guide.
gorski
Like 4
3

List of Telnet Commands for Enigma2 Receivers

The most common Linux commands used in telnet to get the most from your enigma2 receiver.
Learn how to update, upgrade, download and install packages remotely.
thatfellow
Like 11
55