VU+

How To Flash A VU+ DUO 4K Linux Enigma2 Receiver

Flashing the Receiver:






1) Power off the receiver


2) Ensure no other USB devices are plugged into the receiver whilse flashing.



3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible.


4) Power the receiver on.


5) As your Duo 4k starts to power up you should see a update prompt on the receivers display asking you to press the power button, at this point you touch the power button which is located to the…
world-of-satellite.co.uk
Like 1
0

How To Flash A VU+ ZERO 4K Linux Enigma2 Receiver

Flashing the Receiver:

1) Power off the receiver

2) Ensure no other USB devices are plugged into the receiver while flashing.

3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible.

4) Power the receiver on.

5) The WHITE L.E.D VU+ logo to the left front on the receiver will quickly flash two or three times then start to fade in and out slowly.

6) Once completed the WHITE L.E.D will flash rapidly.

7) If in doubt…
world-of-satellite.co.uk
Like 3
5

How To Flash A VU+ UNO 4K SE Linux Enigma2 Receiver

Flashing the Receiver:

1) Power off the receiver

2) Ensure no other USB devices are plugged into the receiver while flashing.

3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible.

4) Power the receiver on.

5) As your UNO 4K SE starts to power up you should see a update prompt on the receivers display asking you to press the power button, at this point you touch the power button which is located

6) The receivers…
world-of-satellite.co.uk
Like 1
7

How To Flash A VU+ ULTIMO 4K Linux Enigma2 Receiver

Flashing the Receiver:

1) Power off the receiver

2) Ensure no other USB devices are plugged into the receiver while flashing.

3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible.

4) Power the receiver on.

5) As your VU+ Ultimo 4K starts to power up you should see a update prompt on the receivers display asking you to press the power button, at this point you touch the power button which is located to the left of…
world-of-satellite.co.uk
Like 1
0

How To Flash A VU+ UNO 4K Linux Enigma2 Receiver

Flashing the Receiver:

1) Power off the receiver

2) Ensure no other USB devices are plugged into the receiver while flashing.

3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible.

4) Power the receiver on.

5) The Blue L.E.D will quickly flash two or three times then start to fade in and out slowly.

6) Once completed the Blue L.E.D will flash rapidly.

7) If in doubt leave the receiver for a full 10 minutes…
world-of-satellite.co.uk
0

How To Flash A VU+ SOLO 4K Linux Enigma2 Receiver

Flashing the Receiver:

1) Power off the receiver

2) Ensure no other USB devices are plugged into the receiver while flashing.

3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible

4) Power the receiver on.

5) As your Solo4K starts to power up you should see a update prompt on the receivers display asking you to press the power button, at this point you press the power button which is located behind the flap on the…
world-of-satellite.co.uk
Like 1
0

How To Flash A VU+ ZERO Linux Enigma2 Satellite Receiver

Flashing the Receiver

1) Power off the receiver

2) Ensure no other USB devices are plugged into the receiver while flashing.

3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible.

4) Power the receiver on.

5) The WHITE L.E.D will quickly flash two or three times then start to fade in and out slowly.

6) Once completed the WHITE L.E.D will flash rapidly.

7) If in doubt leave the receiver for a full 10 minutes…
world-of-satellite.co.uk
12

How To Flash A VU+ SOLO SE Linux Enigma2 Receiver

Flashing the Receiver:

– Fully power the receiver down by the toggle switch at the rear of the receiver.

– Make sure no USB devices are plugged into the receiver at this point.

– Insert the USB stick containing the image files into the USB port on the receiver.

– Power the receiver on.

– The Blue L.E.D will quickly flash two or three times then start to fade in and out slowly.

– Once completed the Blue L.E.D will flash rapidly.

– If in doubt leave the receiver for a full 10 minutes…
world-of-satellite.co.uk
0

How To Flash A VU+ DUO 2 Linux Enigma2 Receiver

Flashing the Receiver:

– Fully power the receiver down via the rocker switch at the rear of the receiver.

– Make sure no USB devices are plugged into the receiver at this point.

– Insert the USB stick containing the image files into one of the USB ports on the receiver.

– Power the receiver on from the rear rocker switch and await instructions.

– As your Duo2 starts to power up you should see a prompt on the receivers display asking you to press the power button, at this point you need to…
world-of-satellite.co.uk
Like 1
0

How To Flash A VU+ SOLO 2 Linux Enigma2 Receiver

Flashing the Receiver:

– Fully power the receiver down via the rocker switch at the rear of the receiver.

– Make sure no USB devices are plugged into the receiver at this point.

– Insert the USB stick containing the image files into one of the USB ports on the receiver.

– Power the receiver on from the rear rocker switch and await instructions.

As your Solo2 starts to power up you should see a prompt on the receivers display asking you to press the power button, at this point you need to…
world-of-satellite.co.uk
Like 1
37

How To Flash A VU+ ULTIMO Linux Enigma2 Receiver

Flashing the Receiver:

– Fully power the receiver down via the rocker switch at the rear of the receiver.

– Make sure no USB devices are plugged into the receiver at this point.

– Insert the USB stick containing the image files into one of the USB ports on the receiver.

– Power the receiver on from the rear rocker switch and await instructions.

As your Ultimo starts to power up you should see a prompt on the receivers display asking you to press the - button, at this point you need to…
world-of-satellite.co.uk
Like 1
0

How To Flash A VU+ UNO Linux Enigma2 Receiver

Flashing the Receiver:

Fully power the receiver down via the rocker switch at the rear of the receiver.

Make sure no USB devices are plugged into the receiver at this point.

Insert the USB stick containing the image files into one of the USB ports on the receiver.

Power the receiver on from the rear rocker switch and await instruction.

As your Vu+ Uno starts to power up you should see a prompt on the receivers display asking you to press the CH - button, at this point you need to press the…
world-of-satellite.co.uk
1

How To Flash A VU+ DUO Linux Enigma2 Receiver

Flashing the Receiver:

Fully power the receiver down via the rocker switch at the rear of the receiver.

Make sure no USB devices are plugged into the receiver at this point.

Insert the USB stick containing the image files into one of the USB ports on the receiver.

Power the receiver on from the rear rocker switch and await instructions.

As your Duo starts to power up the flash progress should automatically begin with a readout of the progress on the receivers display, just sit tight and…
world-of-satellite.co.uk
0

How To Flash A VU+ SOLO Linux Enigma2 Receiver

How to Flash a Vu+ Solo receiver by USB:

Fully power the receiver down by removing the power cord or turning it off at the mains.

Make sure no USB devices are plugged into the receiver at this point.

Insert the USB stick containing the image files into the USB port on the receiver.

Power the receiver on.

The orange / red light on the front of the receiver should be solid while the image is being flashed, DO NOT power off or remove the USB stick.

After a few minutes the orange / red light…
world-of-satellite.co.uk
Like 2
0