Articles

How To Flash A VU+ SOLO SE Linux Enigma2 Receiver

Flashing the Receiver:

– Fully power the receiver down by the toggle switch at the rear of the receiver.

– Make sure no USB devices are plugged into the receiver at this point.

– Insert the USB stick containing the image files into the USB port on the receiver.

– Power the receiver on.

– The Blue L.E.D will quickly flash two or three times then start to fade in and out slowly.

– Once completed the Blue L.E.D will flash rapidly.

– If in doubt leave the receiver for a full 10 minutes…
world-of-satellite.co.uk
0

How To Flash A VU+ ZERO Linux Enigma2 Satellite Receiver

Flashing the Receiver

1) Power off the receiver

2) Ensure no other USB devices are plugged into the receiver while flashing.

3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible.

4) Power the receiver on.

5) The WHITE L.E.D will quickly flash two or three times then start to fade in and out slowly.

6) Once completed the WHITE L.E.D will flash rapidly.

7) If in doubt leave the receiver for a full 10 minutes…
world-of-satellite.co.uk
12

How To Flash A VU+ SOLO 4K Linux Enigma2 Receiver

Flashing the Receiver:

1) Power off the receiver

2) Ensure no other USB devices are plugged into the receiver while flashing.

3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible

4) Power the receiver on.

5) As your Solo4K starts to power up you should see a update prompt on the receivers display asking you to press the power button, at this point you press the power button which is located behind the flap on the…
world-of-satellite.co.uk
Like 1
0

How To Flash A VU+ UNO 4K Linux Enigma2 Receiver

Flashing the Receiver:

1) Power off the receiver

2) Ensure no other USB devices are plugged into the receiver while flashing.

3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible.

4) Power the receiver on.

5) The Blue L.E.D will quickly flash two or three times then start to fade in and out slowly.

6) Once completed the Blue L.E.D will flash rapidly.

7) If in doubt leave the receiver for a full 10 minutes…
world-of-satellite.co.uk
0

How To Flash A VU+ ULTIMO 4K Linux Enigma2 Receiver

Flashing the Receiver:

1) Power off the receiver

2) Ensure no other USB devices are plugged into the receiver while flashing.

3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible.

4) Power the receiver on.

5) As your VU+ Ultimo 4K starts to power up you should see a update prompt on the receivers display asking you to press the power button, at this point you touch the power button which is located to the left of…
world-of-satellite.co.uk
Like 1
0

How To Flash A VU+ UNO 4K SE Linux Enigma2 Receiver

Flashing the Receiver:

1) Power off the receiver

2) Ensure no other USB devices are plugged into the receiver while flashing.

3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible.

4) Power the receiver on.

5) As your UNO 4K SE starts to power up you should see a update prompt on the receivers display asking you to press the power button, at this point you touch the power button which is located

6) The receivers…
world-of-satellite.co.uk
Like 1
7

How To Flash A VU+ ZERO 4K Linux Enigma2 Receiver

Flashing the Receiver:

1) Power off the receiver

2) Ensure no other USB devices are plugged into the receiver while flashing.

3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible.

4) Power the receiver on.

5) The WHITE L.E.D VU+ logo to the left front on the receiver will quickly flash two or three times then start to fade in and out slowly.

6) Once completed the WHITE L.E.D will flash rapidly.

7) If in doubt…
world-of-satellite.co.uk
Like 3
5

How To Flash A VU+ DUO 4K Linux Enigma2 Receiver

Flashing the Receiver:






1) Power off the receiver


2) Ensure no other USB devices are plugged into the receiver whilse flashing.



3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible.


4) Power the receiver on.


5) As your Duo 4k starts to power up you should see a update prompt on the receivers display asking you to press the power button, at this point you touch the power button which is located to the…
world-of-satellite.co.uk
Like 1
0

How to flash a Dreambox DM7020 HD with DreamUP

DM7020HD flashing dreamup
How to flash your Dreambox DM7020 HD with DreamUp

(Hidden Content)




First disconnect the box from main power

start the program "DreamUp



select com port

use network / no network

if network: enter the local IP from your PC, enter a remote IP for your Box



press the "Connect" - button

and then connect the box to main power

please wait now

after the flash loader is transfered into the Box select the firmware by pressing the "Flash" - button



select the…
master G
0

How to flash a Dreambox DM520 HD via a Browser or Telnet

There are two different methods for flashing new firmware to the DM520, via browser or telnet / putty.

To put the DM520 into rescue mode proceed as follows:


Browser method

1. Download and extract your image of choice.

2. Power off receiver via the rocker swith on the rear panel.

3. Power on receiver, within 0.5 of a second you must press and hold the power button on the front panel.
You will see a sequence of colours blinking on the power button. Blue, purple then red, then a constant…
master G
7

How to flash a Dreambox DM525HD via a Browser or Telnet

There are two different methods for flashing new firmware to the DM525, via browser or telnet / putty.

To put the DM525 into rescue mode proceed as follows:


Browser method

1. Download and extract your image of choice.

2. Power off receiver via the rocker swith on the rear panel.

3. Power on receiver, within 0.5 of a second you must press and hold the power button on the front panel.
You will see a sequence of colours blinking on the power button. Blue, purple then red, then a constant…
master G
0

PiP (Picture in Picture) in PurE2

Since I was asked how PiP (Picture in Pictire) actually works in Zgemma STBs with PurE2, here is a guide.
gorski
Like 4
3

PurE2 General Setup

PurE2 will be supported by yours truly, the only (or at least the first) person on Earth who previously wrote a comprehensive tutorial for Enigma2, CamD's, CS, streaming, playback and all the worts..
gorski
Like 9
33

Guide to using Unicable

Guide to using Unicable

A guide to explain possible usages of Unicable/Unicable 2 LNBs. Unicable 2 is also known as JESS
I would like to start off by stating that Unicable LNBs do not need specific tuners. You can use them with a "normal" receiver like: Technomate Nano SE, Vu Solo 2, Vu Duo, Xtrend 8000, Gigablue Quad, Mutant HD51 In the old days, LNBs generally came with a single port. You could only connect to one receiver. Then came Quad LNBs which had four connections, Octo LNBs with…
abu baniaz
Like 2
0

Unicable tuner configuration for Non-FBC tuners

Unicable tuner configuration for Non-FBC tuners:

It should be something similar to this.

Type of LNB/device = SCR (Unicable/Jess)

SCR (Unicable/Jess) type = LNB. Unless you are using a Unicable/Jess switch.

Manufacturer = self explanatory

Model = self explanatory

Position = leave this as 1. (Some LNBs can be programmed and used in combination)

Repeat for every tuner. Make sure that you do not re-use the same user band channel. This applies to all tuners accessing the LNB, even if they…
abu baniaz
Like 2
0

Unicable LNBs and motorised dishes

Unicable LNBs and motorised dishes

A Unicable LNB is a technology which allows multiple users (or multiple tuners) to access satellite broadcasts over a single coaxial cable and eliminates the need for the numerous cables required by a conventional system. In order to satisfy all users of the system the dish must remain permanently orientated to the one satellite that all the users wish to receive programing from. If the dish were to move from its permanent orientation this would disturb the…
abu baniaz
Like 1
0

Brief description of an FBC tuner

Receivers like Vu Solo4K, Vu Ultimo 4K, Gigablue Quad 4K have FBC tuners.


Please do not assume you can only use Unicable with FBC tuners. The two technologies are separate and independent. Yes, you will achieve more if you combine the two.


Brief description of an FBC tuner:




A satellite FBC unit/module consists of two tuners with physical connections and 6 leaf tuners without physical connections.


The two physical connections can have different signal source. E.g. One motorised, one…
abu baniaz
Like 1
0

Brief description of Multi-Switches

Multi-switches:


Unicable2/Jess multi-switches are also available. Like conventional multi-switches, they will allow the user to combine terrestrial and satellite signal and send out to several face plates. These come in various types. Most will require a Quattro LNB, some will take a Quad LNB.
abu baniaz
Like 2
0

Unicable devices and tune failed messages

Unicable devices and tune failed messages


The default delay built into enigma2 between powering up an LNB/switch and sending tuning instructions is not sufficient for Unicable devices. This means from a cold start or first satellite service selection a "tune failed" message is displayed.

Unicable devices are digital devices. That means a finite amount of time is required to elapse for the Unicable device to boot, between being powered up and receiving the first instructions on what to tune.…
abu baniaz
Like 3
0

GT-Sat GT-dLNB1DY and tuner configuration

Below is a guide for configuring the GT-sat Unicable LNB with FBC tuners with only one wire and no splitters

ABM and CrossEPG require sole control of a Tuner, so you will get blackouts while they run.
(As a reminder, FBC tuners and Unicable are two separate technologies.
You can use Unicable LNBs with non-FBC tuners. Eg Dreambox 500, Vu Solo 2, Technomate Nano 3t combo
You can use an FBC tuner with universal (normal) LNBs.
FBC with unicable offers more than FBC with universal.)
For this guide,…
abu baniaz
Like 2
0