Articles

How To Flash A VU+ UNO Linux Enigma2 Receiver

Flashing the Receiver:

Fully power the receiver down via the rocker switch at the rear of the receiver.

Make sure no USB devices are plugged into the receiver at this point.

Insert the USB stick containing the image files into one of the USB ports on the receiver.

Power the receiver on from the rear rocker switch and await instruction.

As your Vu+ Uno starts to power up you should see a prompt on the receivers display asking you to press the CH - button, at this point you need to press the…
world-of-satellite.co.uk
1

How To Flash A VU+ ZERO 4K Linux Enigma2 Receiver

Flashing the Receiver:

1) Power off the receiver

2) Ensure no other USB devices are plugged into the receiver while flashing.

3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible.

4) Power the receiver on.

5) The WHITE L.E.D VU+ logo to the left front on the receiver will quickly flash two or three times then start to fade in and out slowly.

6) Once completed the WHITE L.E.D will flash rapidly.

7) If in doubt…
world-of-satellite.co.uk
Like 3
15

How To Flash A VU+ ZERO Linux Enigma2 Satellite Receiver

Flashing the Receiver

1) Power off the receiver

2) Ensure no other USB devices are plugged into the receiver while flashing.

3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible.

4) Power the receiver on.

5) The WHITE L.E.D will quickly flash two or three times then start to fade in and out slowly.

6) Once completed the WHITE L.E.D will flash rapidly.

7) If in doubt leave the receiver for a full 10 minutes…
world-of-satellite.co.uk
13

How to flash Gigablue HD 800 SE PLUS Linux Enigma2 Receiver

Flashing the Receiver.

1) Power off the receiver
2) Ensure no other USB devices are plugged into the receiver while flashing.
3) Insert the USB stick containing the image files into one of the usb ports on the receiver, rear usb port is advised if possible.
4) Power the receiver on.
5) When the receiver powers up you will see USB then CONF on the receivers display.
6) As soon as you see CONF press the OK button behind the front flap of the receiver to start the flashing process.
7) If…
world-of-satellite.co.uk
Like 1
0

How to install Sundtek USB tuners using Sundtek Control Center

This guide is based using OpenViX images.
1) Power off your receiver.
2) Connect your Sundtek tuner to USB port of your receiver and power on.
3) First we need to install Sundtek Control Center via the OpenViX online plugin feeds. Menu > Plugins > Press Green to download plugins > Select Extensions and press OK, then select sundtekcontrolcenter and press ok. Suntek Control Center will now be installed.



4) Now exit out of all screens and go to Menu > Plugins > Select Sundtek Control Center…
world-of-satellite.co.uk
Like 2
5

How to setup and use OpenViX ‘Client Mode’

Client mode allows you run a client Enigma 2 receiver over an existing network without the need for any signal feeds. All channels and EPG data will be imported from main Server receiver.

1) Only certain skins currently show Client mode setup button. Switch to default ViX Night HD skin to setup. Once setup you can switch back to your preferred skin. To re-access Client Mode setup switch back to ViX Night HD skin.

2) Menu > Setup > Service Searching > Tuner Configuration > See ‘Client Mode’…
world-of-satellite.co.uk
Like 4
6

How to upgrade Edision Nano Series Receivers By USB

Extract the zip file put it in the root (not in a folder) in USB Stick.

From the Menu --> Conditional --> Software Update --> Upgrade By USB,

Select:
Upgrade File: --> e.g. Progressiv_NANO_v.xxxx.abs
Upgrade Mode: --> All SW & bootloader

Press Start.

The receiver will reboot and it's ready.
W@Rp
Like 1
1